Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
- Automatic transmission
Specifications
Electrohydraulic control system - the general information, appointment of basic elements
Self-diagnostics system - the general information and functioning principles
Diagnostics of general condition АТ
Problem diagnostics АТ
Removal and installation трансмиссионной assemblages
Replacement of elements of a suspension bracket трансмиссионной assemblages
Replacement of an epiploon of a casing of lengthening АТ
Condition check, adjustment and replacement of the gauge-switch of the permission of start
Removal and installation of the forward gauge of speed (VSS)
Removal and installation of the back gauge of speed (VSS)
Removal and installation of the gauge of turns of the turbine of the hydrotransformer
Removal, service and installation клапанной assemblages
Replacement of electromagnetic valves of switching, executive electromagnetic valves and the gauge of temperature ATF
Filter ATF replacement
Removal and installation of the module of management of transmission (TCM)
Removal, installation and check of a condition of lines of a path of cooling ATF
Removal, service and installation of components of the lever of selector AT
Removal, installation, check of a condition and adjustment drive selector AT cable
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Filter ATF replacement
Filter replacement should be made without fail at revealing of signs of development of leaks ATF, corrosion, deformations of the case and other mechanical damages. REMOVAL Поддомкратьте the car also establish it on props.
Models 2.0 and 2.5 l
|
|
|
|
Filter ATF is not subject to restoration or repair. |
|
|
1. ST 498545400 remove filter ATF. |
2. Prepare the replaceable filter and grease an epiploon with thin layer ATF. |
|
L models 3.0
Filter ATF
|
|
|
1. Remove локер protection of an arch of the left forward wheel (the Body see the Head).
|
|
2. By means of special key ST 498548500 turn out the filter. |
3. Prepare the replaceable filter and grease an epiploon with thin layer ATF. |
|
Filter ATF assemblage
|
|
|
1. Remove the storage battery.
2. Remove локер protection of an arch of the left forward wheel (the Body see the Head).
3. Lower the car on the earth.
|
|
4. Loosen the collars of fastening of a hose of the oil filter also disconnect a hose from a tube, - mark the end of the hose connected to a tube, the open end of a tube at once закупорьте in order to avoid hit in dirt system. |
5. Give an adjusting nut of a basic arm of the oil filter.
6. Remove filter ATF assemblage.
7. Remove filter ATF with fastening to an arm.
8. Prepare new filter ATF and oil epiploon АТ. |
|
INSTALLATION
Models 2.0 and 2.5 l
|
|
|
1. Manually screw new filter ATF, - try not to damage an epiploon.
2. By means of special key ST 498545400 tighten filter ATF with the demanded effort calculated under the following formula: T2 = L2 / (L1 + L2) хT1, where Т1 = 14 Nanometers, Т2 - effort of a tightening of the filter, L1 - length ST (0.078), L2 - length динамометрического a key. For example, at L2 = 100 mm, Т2 = 7.7 Nanometers.
|
|
Track correctness of a joint динамометрического a key with key ST. |
3. Add in transmission necessary quantity fresh ATF. |
|
L models 3.0
Filter ATF
|
|
|
1. Manually screw new filter ATF, - try not to damage an epiploon.
2. By means of special key ST 498545400 tighten filter ATF with the demanded effort calculated under the following formula: T2 = L2 / (L1 + L2) хT1, where Т1 = 14 Nanometers, Т2 - effort of a tightening of the filter, L1 - length ST (0.078), L2 - length динамометрического a key. For example, at L2 = 100 mm, Т2 = 7.7 Nanometers.
|
|
Track correctness of a joint динамометрического a key with key ST (498545500). |
3. Add in transmission necessary quantity fresh ATF. |
|
Filter ATF assemblage
|
|
| 1. Establish the filter with fastening to an arm and tighten it with demanded effort (14 Nanometers).
2. Establish filter assemblage on the car (the effort of a tightening of fixture makes 16 Nanometers).
3. Remove локер protection of an arch of the left forward wheel (the Body see the Head).
|
|
4. By means of special key ST 498548500 turn out the filter. |
5. Prepare the replaceable filter and grease an epiploon with thin layer ATF.
6. Further operate in an order, the return to an order of dismantle of components, - at hose connection to a tube track correctness of combination of landing labels.
7. In summary add in transmission necessary quantity fresh ATF. |
|
|
On the main page
|