Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
- Automatic transmission
   Specifications
   Electrohydraulic control system - the general information, appointment of basic elements
   Self-diagnostics system - the general information and functioning principles
   Diagnostics of general condition АТ
   Problem diagnostics АТ
   Removal and installation трансмиссионной assemblages
   Replacement of elements of a suspension bracket трансмиссионной assemblages
   Replacement of an epiploon of a casing of lengthening АТ
   Condition check, adjustment and replacement of the gauge-switch of the permission of start
   Removal and installation of the forward gauge of speed (VSS)
   Removal and installation of the back gauge of speed (VSS)
   Removal and installation of the gauge of turns of the turbine of the hydrotransformer
   Removal, service and installation клапанной assemblages
   Replacement of electromagnetic valves of switching, executive electromagnetic valves and the gauge of temperature ATF
   Filter ATF replacement
   Removal and installation of the module of management of transmission (TCM)
   Removal, installation and check of a condition of lines of a path of cooling ATF
   Removal, service and installation of components of the lever of selector AT
   Removal, installation, check of a condition and adjustment drive selector AT cable
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal and installation трансмиссионной assemblages

 PERFORMANCE ORDER

1. Tyre out the car on the lift.
2. Open and prop up a cowl.
3. Disconnect a negative wire from the battery.
4. Remove an air inlet sleeve (see Has undressed Service of components of an inlet air path of the Head of the Power supply system and release).
5. Remove an air cleaner/vozduhopriemnuju the chamber (see Has undressed Service of components of an inlet air path of the Head of the Power supply system and release).
6. Remove a rack of the case of an air cleaner.
7. Disconnect from transmission electroconducting and the plug of grounding of transmission.
8. Remove a starter (the engine Electric equipment see the Head).
9. Remove the terminator of rocking of the power unit (the Engine see the Head).
10. Remove a stopper of a service aperture and, turning the engine for a pulley of a cranked shaft by means of key ST 499977300 (models 2.0)/4999772100 (models 2.5 and 3.0, turn out fastening bolts муфты hydrotransformer couplings to приводному to a disk, - try not to drop bolts in a transmission dome.

11. Fix on a transmission dome блокиратор hydrotransformer ST 498277200.

12. Take probe measurements of level ATF, - in order to avoid hit in картер a dirt at once закупорьте an aperture under installation probeа.

13. By means of adaptation ST 41099AA020 or ST 41099AA010 hang out the power unit from above.

14. Turn out the top bolts of fastening of transmission to the engine.

15. Lift the car and remove protection картера.
16. Remove all sections of system of release of the fulfilled gases (see the Head of the Power supply system and release).
17. Remove a thermofilter.

18. Turn out a drain stopper and let out ATF.

1 — the Pallet
2 — Drain stopper ATF

19. Disconnect from tubes from outside transmissions hoses of cooling ATF and remove directing tube probeа measurements of level ATF.

20. Remove карданный a shaft (Coupling see the Head).
21. Remove a cable of a choice of switchings.
22. Disconnect from the cross-section lever a rack of the stabilizer of cross-section stability and turn out a bolt of fastening of a spherical support to a rotary fist (the Suspension bracket and a steering see the Head).
23. Take подпружиненные pins and liberate from transmission forward power shafts (Coupling see the Head).
24. Give the bottom nuts of fastening of transmission to the engine.

25. Prop up АТ special трансмиссионным a jack, - track, that persistent plates of transmission did not rest against the pallet.

26. Remove a back cross-section beam of transmission.

Efforts of a tightening of carving connections, Nanometer

Т1: 35
Т2: 70

27. Definitively separate transmission from the engine and remove a rubber pillow of a back support of a suspension bracket of the power unit.
28. Installation is made upside-down. Track, that all fixture has been tightened with demanded effort (Specifications and accompanying illustrations to the present Section see).


On the main page