Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
- Automatic transmission
   Specifications
   Electrohydraulic control system - the general information, appointment of basic elements
   Self-diagnostics system - the general information and functioning principles
   Diagnostics of general condition АТ
   Problem diagnostics АТ
   Removal and installation трансмиссионной assemblages
   Replacement of elements of a suspension bracket трансмиссионной assemblages
   Replacement of an epiploon of a casing of lengthening АТ
   Condition check, adjustment and replacement of the gauge-switch of the permission of start
   Removal and installation of the forward gauge of speed (VSS)
   Removal and installation of the back gauge of speed (VSS)
   Removal and installation of the gauge of turns of the turbine of the hydrotransformer
   Removal, service and installation клапанной assemblages
   Replacement of electromagnetic valves of switching, executive electromagnetic valves and the gauge of temperature ATF
   Filter ATF replacement
   Removal and installation of the module of management of transmission (TCM)
   Removal, installation and check of a condition of lines of a path of cooling ATF
   Removal, service and installation of components of the lever of selector AT
   Removal, installation, check of a condition and adjustment drive selector AT cable
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Condition check, adjustment and replacement of the gauge-switch of the permission of start

CHECK

 PERFORMANCE ORDER

1. At infringements of serviceability of functioning of a starter and errors of switchings АТ first of all check up quality of a drive of a gear change. In the absence of visible malfunctions check up the gauge-switch of the permission of start.
2. Disunite a contact socket of electroconducting of the gauge-switch.
3. Check up conductivity of electric contours of the gauge-switch of the permission of start in each of positions of the lever of the selector.

 Also make sure of absence of conductivity of a chain of ignition in all positions of the lever of the selector, except positions «Р» and «N».


4. At infringements of serviceability of functioning of the gauge-switch estimate quality of contact connections of plugs of its socket on the transmission party, - the functional purpose of plugs is explained in the table resulted more low.

Contact quality check in a socket of the gauge-switch of the permission of start


5. Check up conductivity presence in symmetric points at a deviation of the lever of the selector on 1.5 ° in both directions from position «N». In the presence of conductivity in one point and its absence in another, and also in case of symmetry infringement adjust the gauge-switch.

A — There is no conductivity
B — Conductivity is
WITH — 1.5 °

6. Repeat described above check. At detection of deviations adjust приводной a selector cable.

ADJUSTMENT

 PERFORMANCE ORDER

1. Translate the selector lever in position «N».
2. Loosen the three bolts of fastening of the gauge-switch of the permission of start.

3. Insert blocking pin ST 499267300 as it is possible in more vertical position in apertures in the lever and in the case of the gauge-switch of the permission of start.

4. Tighten fixing bolts with demanded effort (3.5 Nanometers).
5. Repeat the checks described in the previous subsection. If during these checks malfunction of the gauge-switch of the permission of start is found out, replace it.

Removal and installation

 PERFORMANCE ORDER

1. Tyre out the car on the lift.
2. Translate the selector lever in position «N».
3. Remove an air cleaner or the air inlet chamber.

4. Disunite a contact socket of the gauge-switch of the permission of start and liberate it from a basic arm.

A the Gauge-switch of the permission of start

5. Lift the car.
6. Remove reception and central sections of an exhaust pipe.

7. Take шплинт from the executive lever of a choice of ranges.

A — the Executive lever of a choice of ranges
In — Shplint
With — a selector Cable
D — the Clamp
Е — the Washer

8. Remove assemblage of a plate with картера transmissions.

A — a selector Cable
B — plate Assemblage

9. Turn out fixing bolts.
10. Having shifted the executive lever of a choice of ranges to the left, translate it in parking position. Remove the gauge-switch of the permission of start.
11. Disconnect from the gauge-switch electroconducting.
12. Installation is made upside-down. Track, that all fixture has been tightened with demanded effort (3.5 Nanometers: for bolts of fastening of the gauge-switch and 24.5 Nanometers: for bolts of fastening of assemblage of a plate), - at a tightening of bolts of fastening of the gauge-switch of the permission of start take advantage of blocking pin ST 499267300.


On the main page