Opel Kadett E

1984-1991 of release

Repair and car operation

11.1. A technical characteristics

THE GENERAL DATA

Forward brakes

Type	Disk, with one piston and a mobile support
Diameter of a disk:
– Models 2,0 of litres	256 mm
– Other models	236 mm
Thickness of a disk:
– The new:
• models 1,2 and 1,3 l the Sedan and the Hatchback	10,0 mm
• models 1,3 of l the Van and the Versatile person	12,7 mm
• l models 1,6	12,7 mm
• l models 1,8	20,0 mm
• l models 2,0	24,0 mm
Is minimum admissible thickness of a brake disk after a repoint (*):
– Models 1,2 and 1,3 l the Sedan and the Hatchback	8,0 mm
– Models 1,3 of l the Van and the Versatile person	10,7 mm
– L models 1,6	10,7 mm
– L models 1,8	18,0 mm
– L models 2,0	22,0 mm
Thickness brake Pads (together with the metal basis):
– The new	15,5 – 15,9 mm
– Is minimum admissible	7,0 mm

* If deterioration of disks has reached is minimum admissible thickness, use only one complete set brake колодок then disks are subject to replacement is supposed.

Back brakes

Type
Models 2,0 of l GTE	Disk, with a support with two pistons
Other models	The drum-type
Diameter of a drum
The new:
– Models till 1989:
• the Hatchback and the Versatile person of 1,3 l with a mechanical transmission	200 mm
• all other models the Versatile person and all the Van	230 mm
– Models since 1989 (all models)	200 mm
The maximum diameter of a drum:
– Models till 1989:
• the Hatchback and the Versatile person of 1,3 l with a mechanical transmission	201 mm
• all other models the Versatile person and all the Van	231 mm
– Models since 1989 (all models)	201 mm
The maximum ovality of a brake drum	0,1 mm
The minimum depth of heads of rivets in a brake overlay	0,5 mm
Diameter of a brake disk	260 mm
Thickness of a brake disk:
– The new	10,0 mm
– After a repoint (*)	8,0 mm
Thickness brake Pads (together with the metal basis):
– The new	15,0 mm
– Is minimum admissible	7,0 mm

* If deterioration of disks has reached is minimum admissible thickness, use only one complete set brake колодок then disks are subject to replacement is supposed.

The tightening moments

Prorolling unions	9 Nanometers
Connection of a brake tube / of a hose	25 Nanometers
Support of a forward brake:
– Support GMF:
• bolts of fastening of the holder of a support	95 Nanometers
• bolts of fastening of a support to the holder of a support	95 Nanometers
– Support ATE:
• bolts of fastening of the holder of a support	95 Nanometers
• directing fingers	30 Nanometers
Bolts of fastening of a support of a back brake	60 Nanometers
Bolt of fastening of the working brake cylinder	9 Nanometers
Nuts of fastening of the main brake cylinder	18 Nanometers
Hydraulic connection of the working brake cylinder	11 Nanometers
The valve of regulation of pressure:
– The valve established on a back axis – the Versatile person and the Van	20 Nanometers
– The valve established on the main brake cylinder:
• cylinder GMF	40 Nanometers
• cylinder ATE	12 Nanometers
The persistent screw of the main brake cylinder (ATE)	6 Nanometers
The vacuum amplifier of brakes to an arm	18 Nanometers
Arm of the vacuum amplifier of brakes to a partition of a motor compartment	18 Nanometers
Bolts of fastening of a brake board of a drum-type brake (it is necessary to put the means interfering unscrewing of bolts) on a carving	30 Nanometers
Bolts of fastening of the lever of a manual brake	20 Nanometers
Components ABS:
– The hydraulic block to an arm	8 Nanometers
– The forward gauge of speed of a wheel	8 Nanometers
– The back gauge of speed of a wheel	15 Nanometers