Opel Kadett E

1984-1991 of release

Repair and car operation


Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
- 11. Brake system
   11.1. A technical characteristics
   + 11.2. Prorolling of hydraulic brake system
   11.3. Brake pipelines and hoses
   + 11.4. Lobbies brake Pads
   11.5. Replacement back brake колодок on disk brakes
   11.6. Replacement back brake колодок on drum-type brakes
   11.7. Check, removal and installation of a forward brake disk
   11.8. Check, removal and installation of a back brake disk
   11.9. Removal, check and installation of a brake drum
   + 11.10. A support of a forward brake
   + 11.11. A support of a back disk brake
   + 11.12. The back working brake cylinder
   + 11.13. The main brake cylinder
   + 11.14. Valves of adjustment of pressure
   11.15. Replacement of the unidirectional valve of the vacuum amplifier of brakes
   11.16. Check, removal and installation of the vacuum amplifier of brakes
   11.17. Removal and installation of a pedal of a brake
   11.18. Removal and installation of a cable of a manual brake
   11.19. Removal and installation of the lever of a manual brake
   11.20. Replacement brake колодок a manual brake on back disk brakes
   + 11.21. Antiblocking system of brakes (ABS)
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes

11.5. Replacement back brake колодок on disk brakes
PERFORMANCE ORDER
1. At presence remove caps of wheels, then ослабьте bolts of fastening of back wheels.
2. Lift a back part of the car and fix on supports.
3. Remove back wheels.
4. Check up a condition and a thickness of overlays brake колодок back wheels. Even if deterioration borders were reached only by one brake колодка, replace back brake Pads in the complete set.
5. Note an arrangement of the spring supporting brake Pads, then, using a steel core or a screw-driver, from lateral aspect squeeze out the bottom and top fingers of fastening brake колодок.
6. Remove a spring supporting brake Pads.
7. Take away brake Pads from a brake disk, then flat-nose pliers take external brake колодку and a lining established between brake колодкой and the holder of a support.
8. Take internal brake колодку and a lining.
9. Clear a dust and a dirt from a support, and a rust from edge of a brake disk. If Pads are suitable to the further operation, clear them, using a wire brush and rags.
10. If will be established new brake Pads, press the piston into a support a wooden core or the hammer handle, thus watch, that the piston has not warped also surfaces of the piston and dusterа have not been damaged.
11. At вдвигании the piston the brake liquid is superseded from the brake cylinder in пополнительный a tank, therefore constantly observe of liquid level in a tank, and if necessary pump out its small amount.
12. Check up a condition of a brake disk on presence of flutes, scratches or cracks. In the presence of defects replace a brake disk.
13. Apply a thin film greasings for brake system on the top and bottom end faces of the metal basis brake колодок.
14. Establish brake Pads in a support. Check up that Pads freely move in a support.
15. Establish a spring supporting brake Pads, then from the inside establish fingers of fastening brake колодок. Thus simultaneously press a spring supporting brake Pads.
16. Similarly replace brake Pads on the second wheel.
17. Establish wheels and lower the car on the earth.
18. Tighten bolts of fastening of a wheel the demanded moment.
19. Some times press a brake pedal that brake Pads have nestled on a brake disk.
20. Check up level of a brake liquid.
21. After installation new brake колодок avoid sharp braking during the first 200 km of run of the car.


On the main page