Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
- 11. Brake system
   11.1. A technical characteristics
   + 11.2. Prorolling of hydraulic brake system
   11.3. Brake pipelines and hoses
   + 11.4. Lobbies brake Pads
   11.5. Replacement back brake колодок on disk brakes
   11.6. Replacement back brake колодок on drum-type brakes
   11.7. Check, removal and installation of a forward brake disk
   11.8. Check, removal and installation of a back brake disk
   11.9. Removal, check and installation of a brake drum
   + 11.10. A support of a forward brake
   + 11.11. A support of a back disk brake
   + 11.12. The back working brake cylinder
   + 11.13. The main brake cylinder
   + 11.14. Valves of adjustment of pressure
   11.15. Replacement of the unidirectional valve of the vacuum amplifier of brakes
   11.16. Check, removal and installation of the vacuum amplifier of brakes
   11.17. Removal and installation of a pedal of a brake
   11.18. Removal and installation of a cable of a manual brake
   11.19. Removal and installation of the lever of a manual brake
   11.20. Replacement brake колодок a manual brake on back disk brakes
   + 11.21. Antiblocking system of brakes (ABS)
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes





11.6. Replacement back brake колодок on drum-type brakes
THE GENERAL DATA

Elements of a back drum-type brake

1 – разжимная a lath,
2 – a clamp,
3 – a wheel of a regulator,
4 – the lever of a regulator,
5 – a spring of the lever of a regulator,
6 – an arm of the lever of a regulator,
7 – the lever of a manual brake,
8 – the top returnable spring

Check

PERFORMANCE ORDER
1. For check brake колодок it is recommended to remove a brake drum. In this case it is possible to check up a condition of the working brake cylinder also.
2. Deterioration of overlays brake колодок can be checked up and without removal of a brake drum through viewing apertures in a brake board after removal заглушки from an aperture.
3. Using a small lamp and a mirror, through an aperture in a brake board check up a thickness of an overlay brake Pads.
4. Even if deterioration borders were reached only by one brake колодка, necessarily replace all back brake Pads in the complete set.

Replacement

PERFORMANCE ORDER
1. At presence remove caps of back wheels, then ослабьте bolts of fastening of wheels.
2. Lift a back part of the car and fix on supports.
3. Remove back wheels.
4. Completely release a manual brake.
5. Unscrew the screw of fastening of a brake drum and remove a brake drum.
6. If the brake drum is kept brake колодками, remove заглушку from a viewing aperture of a brake board and through an aperture move a control lever of a manual brake to brake колодке, thus brake Pads will depart from a drum and the drum will easily act in film.
7. Note adjusting position of all elements of a back brake.
8. Measure a thickness of a frictional overlay brake Pads and at its deterioration in any point till is minimum admissible thickness replace all four brake Pads.
9. Also Pads it is necessary to replace, if though one of колодок is polluted by oil as there is no way of degreasing brake колодок.
10. If brake Pads are worn non-uniformly out or polluted by oil, reveal and eliminate the reason of it before installation new brake колодок.
11. Using flat-nose pliers, remove a plate (it is specified by an arrow) fixing springs Pads, pressing a plate and turning it on 90 .
12. Remove a spring and take clamp pins.
13. Disconnect from a control lever a cable of a manual brake (the arrow specifies cable fastening to the lever of a manual brake).
14. Disconnect from brake колодок the top returnable spring and remove Pads from a brake board.
15. If necessary remove brake Pads together with a spring and разжимной a lath.
16. Remove a nave. Be careful not to damage rubber covers of the working brake cylinder. Before removal note position of a returnable spring and an adjusting lath.
17. Do not remove simultaneously brake Pads the left and right back wheel not to mix a detail brake колодок.
18. For prevention of an exit of pistons from the working brake cylinder establish on pistons an elastic band or fix their spring скобой. Do not press a brake pedal at the removed brake drum.
19. Being careful and security measures, clear all traces of a brake dust from a brake board.
20. Apply a thin film high-temperature greasing on places of contact brake колодок and a brake board.
21. If on overlays brake колодок there is a liquid which has flowed out from the working brake cylinder or the bearing of a nave, define the reason вытекания and eliminate it.
22. If brake Pads acted in film in gathering, note position of elements and separate from each other brake Pads, springs and разжимную a lath.
23. If brake Pads the left and right back wheel acted in film simultaneously, do not mix a detail. Cores with a carving of adjusting laths of the left and right wheel are noted by letters L or R, and other details are identified by colour: black – for a left-hand side and silvery for the right party.
24. Disassemble and clear an adjusting lath.
25. Check up a condition of returnable springs and, if necessary, replace them.
26. If on new brake колодках there is no control lever of a manual brake remove it with old brake Pads and establish on the new.
27. Fix шарнирный a finger of a control lever of a manual brake a spring ring.
28. If elements of a back brake are established in gathering, collect new brake Pads, a spring and an adjusting lath.
29. For simplification of installation move apart adjusting разжимную a lath.
30. Establish on brake Pads the top returnable spring.
31. Establish on conducting brake колодку a spring of the lever of a regulator (the arrow specifies an installation direction).
32. Remove from the working brake cylinder an elastic band or spring скобу, establish knot brake колодок on a brake board, thus be careful not to damage covers of the working brake cylinder.
33. Establish pins of clamps brake колодок, springs and plates of fastening of a spring.
34. Connect a cable of a manual brake to the lever on back brake колодке, then establish a nave of a back wheel and adjust люфт in the bearing.
35. Rotating a wheel of an adjusting lath, reduce length разжимной laths to take away brake Pads from a brake drum.
36. Check up that the reference point of a stop of the lever of a manual brake is established against edge brake Pads, then establish a brake drum.
37. Make replacement brake колодок on the second back wheel.
38. After replacement brake колодок adjust a backlash between them and a brake drum for what 15–20 times press a brake pedal. By pedal pressing at normal work of an adjusting lath the clicks published by an adjusting lath should be audible.
39. Check up and if it is necessary, adjust a manual brake.
40. Establish wheels and lower the car on the earth.
41. Tighten bolts of fastening of a wheel the demanded moment and at presence establish a wheel cap.
42. After installation new brake колодок avoid sharp braking during the first 200 km of run of the car.

On the main page