Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
- 6. Fuel and exhaust systems
   - 6.1. Models with the carburettor
      6.1.1. A technical characteristics
      6.1.2. Use unleaded gasoline
      6.1.3. Removal and installation of the case of the air filter
      6.1.4. System of adjustment of temperature of air arriving in the engine
      6.1.5. Check, removal and installation of the fuel pump
      6.1.6. Removal and installation of the gauge of level of fuel
      6.1.7. Removal and installation of a fuel tank
      6.1.8. Removal, installation and adjustment of a cable of an accelerator
      6.1.9. Removal and installation of a pedal of an accelerator
      6.1.10. Removal, installation and adjustment of a cable of management air заслонкой
      - 6.1.11. Carburettors
         + 6.1.11.1. Adjustments on the carburettor 32 TL
         + 6.1.11.2. Adjustments on the carburettor 35 PDSI
         + 6.1.11.3. Adjustments on the carburettor 1В1
         - 6.1.11.4. Adjustments on the carburettor 2Е3
            + 6.1.11.4.1. The carburettor is established on the engine
            - 6.1.11.4.2. The carburettor is removed from the engine
               6.1.11.4.2.1. Position of a cam of the accelerated turns of idling
               6.1.11.4.2.2. A backlash throttle заслонки the accelerated turns of idling
               6.1.11.4.2.3. Productivity of the accelerating pump
         + 6.1.11.5. Adjustments on carburettor Varajei II
      6.1.12. Check of the electromagnetic valve of a stopping delivery of fuel
      6.1.13. Removal and carburettor installation
      + 6.1.14. Carburettor repair
      6.1.15. Removal and installation of an inlet collector
      6.1.16. Removal and installation of a final collector
      6.1.17. Removal and installation of a heater of an inlet collector
      6.1.18. Removal and exhaust system installation
   + 6.2. Models with system of injection of fuel
   + 6.3. Models with engines 16D and 16DA
   + 6.4. Models with engines 17D and 17DR
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes





6.1.11.4.2. The carburettor is removed from the engine

6.1.11.4.2.1. Position of a cam of the accelerated turns of idling
THE GENERAL DATA

Adjustment of a cam of the accelerated turns of idling

1 – a cam,

2 – the adjusting lever,

3 – the drive lever заслонки (it is necessary to press in an arrow direction),

4 – the screw of adjustment of turns of accelerated idling,

And = 0,2–0,8 mm

PERFORMANCE ORDER
1. Check up correctness of adjustment of moving заслонки which is described in subsection 6.1.11.4.1.3. If it is not executed, uncover заслонки.
2. Open throttle заслонку, then easy pressing of a finger of a hand the drive lever заслонки close air заслонку. Release throttle заслонку.
3. Check up that the adjustment screw leans against the highest step of a cam of adjustment of the accelerated single turns. Otherwise check up correctness of placing of a returnable spring заслонки and, if necessary, adjust it, turning in the lever 2.
4. Establish and fix screws a cover заслонки, thus adjusting labels should be combined.

On the main page