Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
- 6. Fuel and exhaust systems
   - 6.1. Models with the carburettor
      6.1.1. A technical characteristics
      6.1.2. Use unleaded gasoline
      6.1.3. Removal and installation of the case of the air filter
      6.1.4. System of adjustment of temperature of air arriving in the engine
      6.1.5. Check, removal and installation of the fuel pump
      6.1.6. Removal and installation of the gauge of level of fuel
      6.1.7. Removal and installation of a fuel tank
      6.1.8. Removal, installation and adjustment of a cable of an accelerator
      6.1.9. Removal and installation of a pedal of an accelerator
      6.1.10. Removal, installation and adjustment of a cable of management air заслонкой
      + 6.1.11. Carburettors
      6.1.12. Check of the electromagnetic valve of a stopping delivery of fuel
      6.1.13. Removal and carburettor installation
      - 6.1.14. Carburettor repair
         6.1.14.1. The carburettor 32 ТL
         6.1.14.2. The carburettor 35 PDSI
         6.1.14.3. The carburettor 1В1
         6.1.14.4. The carburettor 2Е3
         + 6.1.14.5. Carburettor Varajet II
      6.1.15. Removal and installation of an inlet collector
      6.1.16. Removal and installation of a final collector
      6.1.17. Removal and installation of a heater of an inlet collector
      6.1.18. Removal and exhaust system installation
   + 6.2. Models with system of injection of fuel
   + 6.3. Models with engines 16D and 16DA
   + 6.4. Models with engines 17D and 17DR
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes





6.1.14. Carburettor repair

6.1.14.1. The carburettor 32 ТL
THE GENERAL DATA

Arrangement of the screw of fastening of an arm of support of a cable of management air заслонкой, заглушки, the screw of adjustment of quality of a mix and idling turns

And – the screw of fastening of an arm of support of a cable of management air заслонкой,

In – заглушка,

With – the screw of adjustment of quality of a mix,

D – the screw of adjustment and idling turns

Arrangement in a carburettor cover заглушек, a jet of idling, an additional air jet and a jet of a fuel mix

And, In – заглушки,

With – a jet of idling,

D – an additional air jet,

Е – a jet of a fuel mix

The prevention

If the carburettor demands major repairs, economically it is more favourable to replace the carburettor. It is usually necessary to assort the carburettor for clearing of jets and carburettor channels.


PERFORMANCE ORDER
1. Remove the carburettor from the engine.
2. Using suitable solvent or gasoline, clear an external surface of the carburettor and dry up it. Prepare a pure workplace.
3. Remove a returnable spring throttle заслонки from draught and an arm sideways the carburettor.
4. Disconnect a vacuum hose from a branch pipe of the vacuum chamber located on the case throttle заслонок.
5. Unscrew 4 screws (are specified by arrows) fastenings of a cover of the carburettor.
6. Uncover the carburettor the carburettor.
7. In the carburettor basis unscrew the screw (it is specified by an arrow), крепящий the case air заслонки to the case поплавковой chambers, and divide cases.
8. Unscrew the screw, крепящий an arm of support of a cable of management air заслонкой to the case air заслонки and remove it (fig. the Arrangement of the screw of fastening of an arm of support of a cable of management air заслонкой, заглушки, the screw of adjustment of quality of a mix and idling turns see). Release a clamp and take from a casing a sealing ring.
9. Screw in against the stop screws of adjustment of quality of a fuel mix and idling turns, but thus count quantity of turns of screws, then unscrew screws completely.
10. Unscrew four screws and uncover diaphragms of the accelerating pump and a spring the case поплавковой chambers.
11. On the other hand cases поплавковой chambers unscrew three screws and uncover diaphragms of the mechanism of enrichment and a spring.
12. Take a spray from a casing.
13. Using выколотку, beat out a rotary axis of floats (it is specified by arrows) and, using flat-nose pliers, take it from a nest.
14. Remove floats and a lining of a cover of the carburettor.
15. Remove the needle valve of the carburettor, then unscrew the main jet (it is specified by an arrow).
16. Note an arrangement and unscrew all jets and заглушки from a carburettor cover (fig. the Arrangement in a carburettor cover заглушек, a jet of idling, an additional air jet and a jet of a fuel mix see). Unscrew эмульсионную a tube from an aperture of an additional air jet.
17. Take from диффузора the main spray.
18. Unscrew a stopper and take the fuel filter located adjacently with a branch pipe of giving of fuel.
19. If necessary remove from the top cover of the carburettor the vacuum chamber together with the draught operating air заслонкой.
20. Remove a cam and a spring, disconnect draught from a cam and the lever of a drive air заслонки and remove knot in gathering (And – draught screws заслонки, In – spring скобы).
21. Clear carburettor details in gasoline and blow their compressed air.
22. Blow compressed air all jets and channels in the carburettor, but thus do not use a wire.
23. Check up a condition of all axes and draughts on presence of deterioration and the increased backlash. In the presence of defects replace the worn out details.
24. Check up a condition of diaphragms and replace them in the presence of punctures and pollution.
25. Check up a condition and tightness of a float. If in a float there is a fuel, replace it.
26. Blowing the needle valve, check up its tightness in the closed position. In the absence of tightness replace the needle valve.
27. Collect the carburettor in sequence, return dismantling, and make the basic adjustments of the carburettor.
28. Check up height of installation of a float and, if necessary, turning in the lever, establish the demanded height (And – a place of measurement of height of installation of a float, In – a place for adjustment of height of installation of a float).
29. Establish the carburettor on the car and adjust turns of idling and quality of a fuel mix.

On the main page