Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
- The engine
   Specifications
   Check компрессионного pressure in cylinders and tightness of the block
   Diagnostics of a condition of the engine with vacuum gauge application
   System of greasing of the engine - the general information
   - The procedures of the repair which has been not connected with extraction of the engine from the car, - four-cylinder engines
      Reduction of the piston of the first cylinder in position ВМТ
      Check and adjustment клапанных backlashes
      Removal and installation of a pulley of a cranked shaft
      Removal and installation of forward covers of drive ГРМ
      Removal and installation of a belt of drive ГРМ, check of a condition of components
      Removal, check of a condition and installation of cogwheels of camshafts
      Removal and installation of a cogwheel of a cranked shaft
      Натяжитель газораспределительного a belt - the general information and a functioning principle
      Removal, check of a condition and installation of elements of a drive of valves
      Removal and installation of camshafts
      Removal and installation of heads of cylinders
      Removal and pallet installation картера and маслозаборника
      Removal, service and installation of the oil pump
      Check of pressure of impellent oil
      Removal and installation of the gauge-switch of pressure of oil
      Removal, check of a condition and installation of a flywheel/privodnogo of a disk
      Replacement of support of a suspension bracket of the power unit
   + The procedures of the repair which has been not connected with extraction of the engine from the car, - six-cylinder engines
   + The general and major repairs of engines
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal and installation of a pulley of a cranked shaft

REMOVAL

 PERFORMANCE ORDER

1. Remove V-shaped приводной a belt (Routine maintenance see the Head).
2. Turn out a bolt of a pulley of a cranked shaft, - blocking of a cranked shaft from проворачивания is made by means of the special tool (ST 499977300 - models 2.0 of l or ST 499977100 - models 2.5).

3. Remove a pulley of a cranked shaft.

INSTALLATION

 PERFORMANCE ORDER

1. Establish a pulley of a cranked shaft on the regular place.
2. Blow air a carving aperture under a pulley bolt.
3. Grease a carving part and a persistent surface of a bolt of a pulley of a cranked shaft with impellent oil.
4. Temporarily tighten bolts with effort of 44 Nanometers
5. On l models 2.0 block a shaft from проворачивания special tool ST 499977300 and wrap a bolt of a pulley of a cranked shaft with demanded effort (127 Nanometers: models 2.0 of l/177 of Nanometer: models 2.5). For keeping of a cranked shaft take advantage of the special tool.
6. Make sure that the corner of an inhaling of a bolt of a pulley of a cranked shaft makes not less than 45 ° (models 2.0)/65 ° (models 2.5.

 If the corner of an inhaling of a bolt of a pulley of a cranked shaft makes less stipulated value, the bolt can be damaged! In case of need make bolt replacement, - as replaceable it is necessary to use a bolt № 12369АА011.

7. The order of a tightening of a replaceable bolt is made in the manner similar described above for bolt, were in the use (the tightening corner should lie in a range 40 ÷ 60 °/65 ÷ 75 ° accordingly – the goniometric scale is put on a belt cover).

8. Establish натяжитель a belt of a drive of compressor K/V.

9. Establish приводной a belt and make adjustment of its tension (Routine maintenance see the Head).


On the main page