Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
- 6. Fuel and exhaust systems
   - 6.1. Models with the carburettor
      6.1.1. A technical characteristics
      6.1.2. Use unleaded gasoline
      6.1.3. Removal and installation of the case of the air filter
      6.1.4. System of adjustment of temperature of air arriving in the engine
      6.1.5. Check, removal and installation of the fuel pump
      6.1.6. Removal and installation of the gauge of level of fuel
      6.1.7. Removal and installation of a fuel tank
      6.1.8. Removal, installation and adjustment of a cable of an accelerator
      6.1.9. Removal and installation of a pedal of an accelerator
      6.1.10. Removal, installation and adjustment of a cable of management air заслонкой
      + 6.1.11. Carburettors
      6.1.12. Check of the electromagnetic valve of a stopping delivery of fuel
      6.1.13. Removal and carburettor installation
      - 6.1.14. Carburettor repair
         6.1.14.1. The carburettor 32 ТL
         6.1.14.2. The carburettor 35 PDSI
         6.1.14.3. The carburettor 1В1
         6.1.14.4. The carburettor 2Е3
         + 6.1.14.5. Carburettor Varajet II
      6.1.15. Removal and installation of an inlet collector
      6.1.16. Removal and installation of a final collector
      6.1.17. Removal and installation of a heater of an inlet collector
      6.1.18. Removal and exhaust system installation
   + 6.2. Models with system of injection of fuel
   + 6.3. Models with engines 16D and 16DA
   + 6.4. Models with engines 17D and 17DR
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes





6.1.14.2. The carburettor 35 PDSI
THE GENERAL DATA

Details of the carburettor 35 PDSI

1 – a cover,
2 – a lining,
3 – the needle valve,
4 – скоба axes of a float,
5 – an axis of a float,
6 – a float,
7 – the case of the carburettor,
8 – the valve blocking giving of fuel,
9 – a spring of a diaphragm of the accelerating pump,
10 – a diaphragm of the accelerating pump,
11 – a cover of a diaphragm of the accelerating pump,
12 – a nut of draught of the accelerating pump,
13 – a spring,
14 – draught of the accelerating pump,
15 – диффузор,
16 – a lining,
17 – the screw of adjustment of turns of idling,
18 – the screw of adjustment of quality of a fuel mix,
19 – knot throttle заслонки,
20 – the screw of adjustment of the accelerated turns of idling,
21 – draught of the accelerated turns of idling,
22 – a main fuel jet,
23 – заглушка a main jet,
24 – the valve of enrichment of partial loading

Carburettor major repairs are necessary only at deterioration of details of the carburettor. Usually for restoration of normal working capacity of the carburettor it is enough to uncover carburettor and to clear chambers of the carburettor of a deposit and to blow jets the compressed air.

PERFORMANCE ORDER
1. Remove the carburettor from the engine and clear an external surface of the carburettor. Remove скобу, which крепит draught of the accelerated turns of idling for the lever on an axis air заслонки.
2. Unscrew six screws and uncover the carburettor.
3. Unscrew the needle valve.
4. Unscrew a carving stopper and take a measuring pin.
5. Remove spring скобу, take an axis of a float and remove a float from the carburettor.
6. The valve of enrichment of partial loading is screwed in in the basis of a ball of a float.
7. Insert a screw-driver through an aperture, take a ball of a float and unscrew the main jet.
8. The case air заслонки is screwed on the case of the carburettor by two screws and for its removal at first disconnect draught of the accelerating pump, then unscrew screws.
9. Unscrew four screws and remove the accelerating pump.
10. Clear all details and check up their condition on presence of deterioration or damages.
11. Blow compressed air all jets and carburettor channels. For clearing of jets do not use a wire, otherwise calibration of jets will be broken.
12. Replace all sealing rings, linings and diaphragms.
13. The data for adjustment of position of a float is absent.

14. Collect the carburettor in sequence, return dismantling, and make carburettor adjustments.

On the main page