Audi A3

Since 1997 of release

Repair and car operation

Replacement of lamps of external illumination

PERFORMANCE ORDER

1. Switch off the switch of a corresponding lamp.
2. Switch off ignition.

Near and far light

ATTENTION

Lamps Н7 are under pressure and can burst at performance of their replacement. Therefore at replacement of lamps Н7 it is necessary to use mittens and goggles.

PERFORMANCE ORDER

1. Open a cowl.
	2. Uncover behind a headlight. For this purpose press on both laths–1 downwards and disconnect them from holders–2. Cast away a cover–3 above back and take out from the bottom directing.
	3. Расстыкуйте a socket of a lamp of a passing light–3 or a headlight–4. 1 – the electric motor of adjustment of range of light, 2 – a headlight socket.
4. Raise from a headlight underside a spring clip in the centre a little and incline it in an arrow direction.
5. Расстыкуйте a socket of a lamp of a passing light.
6. Press and open a spring clip over a lock pad.
7. Take out a lamp from a reflector. ATTENTION Do not take a lamp naked fingers. The print of fingers evaporates and besieged on a reflector, reducing a light stream of a lamp. Necessarily establish a lamp of the same execution. Stains on a lamp are eliminated by the pure scarf moistened in spirit.
8. Insert a new lamp so that pads have entered into corresponding grooves on the case.
9. Cast away back spring скобу and fix in pads.
10. Join a socket on a cartridge.
11. Put a cover on an underside of a headlight and fix a spring clip.
12. Check up adjustment of headlights in conditions HUNDRED.
13. Close a cowl.

Parking light

PERFORMANCE ORDER

1. Open a cowl.
2. Uncover behind a headlight. For this purpose above press downwards both plastic laths and release them. Cast away a cover back.
	3. Take out a cartridge–1 with a lamp from a reflector. 2 – the headlight tip.
4. Take out a lamp from a cartridge.
5. Insert into a cartridge a new lamp.
6. Press a cartridge with a lamp into a reflector against the stop.
7. Connect a cover on a headlight underside below and fix it above.
8. Close a cowl.

The forward index of turn

PERFORMANCE ORDER

1. Remove a forward signal of turn, address to subsection Removal and installation of the forward index of turn.
	2. Turn to the left a cartridge of a lamp–1 and take out it from the case–3.
3. Slightly press a lamp–2 into a cartridge, turn on 90 ° (1/4 turns) to the left and take out a lamp. ATTENTION Do not concern flasks of a new lamp with hand fingers. Use a pure rag or put on thin gloves.
4. Insert a new lamp, slightly press on it and turn to the right.
5. Insert a cartridge with a lamp into a reflector and turn to the right. ATTENTION The cartridge should be fixed.
6. Establish the turn index, address to subsection Removal and installation of the forward index of turn.

The lateral repeater of the index of turn

PERFORMANCE ORDER

	1. Press fingers the turn index forward in a headlight direction (an arrow illustrations) and take out it in a back part from an aperture in a wing–3. At removal the lamp is displaced forward, overcoming force of a plastic spring–4.
2. Remove a cartridge of a lamp–5 from the case–6.
3. Take out a lamp from a cartridge and replace.
4. Insert a cartridge with a lamp into the case.
5. Insert a lamp behind into plastic hooks in a wing aperture, on the other hand press and fix a plastic spring.

Back lantern

PERFORMANCE ORDER

1. Open a back door.
2. Open a luggage carrier pocket at the left or on the right. For this purpose turn a clip above at a pocket cover on the left.
	3. Расстыкуйте a socket–3 back lanterns.
4. Compress lock laths–2 and thus release the holder of a lamp.
5. Take out the holder of a lamp–1.
6. The damaged lamp slightly press into a cartridge, turn on 90 ° (1/4 turns) to the left and take out. ATTENTION Insert a new lamp, slightly press it and turn to the right.
7. Insert the holder of a lamp into a back lantern, press and fix.
8. Join a socket at the holder of a lamp.
9. Close a cover of a pocket of a luggage carrier and fix a clip turn to the right.
10. Close a back cover.

Lantern of illumination of licence plate

PERFORMANCE ORDER

1. Open a back door.
	2. Turn on in a lath–1 on two screws with crosswise шлицами–3. On an illustration the lamp of illumination of the right licence plate is represented.
3. Take out the holder of a lamp from a lath and расстыкуйте a socket–2.
4. Take out a lamp–4 of a cartridge and replace. Thus watch reliability of installation of a lamp. If necessary slightly turn in clips.
5. Join a socket.
6. Insert the holder of a lamp into a lath and fix screws.
7. Close a back door.

Additional stoplight

The additional stoplight is located at the top of a back door behind back glass.

PERFORMANCE ORDER

1. Remove the top internal facing of a back door, address to subsection Removal and installation of facing of a door of a back.
	2. Расстыкуйте a socket–6.
3. Turn out the screw of fastening from–4 of насечной rivets–1.
4. Disconnect a hook–7 of an aperture and remove a stoplight.
5. Remove рассеиватель–3 from the holder of a lamp–2.
6. Take out the damaged lamp–5 of the holder of a lamp–2 and insert a new lamp.
7. Insert the holder of a lamp with рассеивателем and fix its screws.
8. Join a socket.
9. Establish into place internal facing of a back door, address to subsection Removal and installation of facing of a door of a back.

On the main page