Audi A3

Since 1997 of release

Repair and car operation



Audi A3
+ The maintenance instruction
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Manual box of a gear change
+ Automatic transmission and models with a full drive
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Electric equipment of system of comfort
   Diagnostics of malfunctions of an onboard electric equipment - the general information
   Check of the electric motor of a screen wiper
   Check of warmed back glass
   Stoplight check
   Removal, installation and check of a sound signal
   Safety locks
   Fusible inserts - the general information
   Chain breakers (thermal relays)
   The relay
   Replacement of batteries of a key of remote control
   Replacement of the battery/lamp of a key with illumination
   Anticreeping blocking
   Illumination devices
   Replacement of lamps of external illumination
   Replacement of bulbs of internal illumination
   Removal and headlight installation
   Removal and installation of the electric motor of adjustment of range of light
   Removal and installation of the forward index of turn
   Removal and installation of a back lantern
   Adjustment of light of headlights
   Devices
   Removal and control panel installation
   Removal and installation подрулевого the switch
   Removal and installation of switches and lamps
   Removal, installation and radio receiver coding
   Input of a code of a radio receiver
   Removal and loudspeaker installation
   Removal and installation of the aerial of a roof
   Additional installation of a radio telephone on in special way prepared models
   Removal and installation of the electric motor of a forward screen wiper
   Removal and installation of the lever and the electric motor of a back screen wiper
   Removal and installation of a cleaner of back glass
   Removal and installation of the tank from the pump стеклоомывателя
   Elements темпостата
+ Electroschemes





Removal and installation подрулевого the switch

THE GENERAL DATA

Into structure подрулевого the switch enter: both switches of the index of turns/headlights and a screen wiper.

REMOVAL

PERFORMANCE ORDER
1. Disconnect a negative cable (–) the storage battery at the switched off ignition.
ATTENTION

Thereof the information from electronic blocks of memory, as, for example, a radio receiver code is erased. Without a code the radio receiver can be included only the manufacturer or HUNDRED AUDI. Therefore familiarise with materials of subsection Input of a code of a radio receiver.
Read necessarily remarks on security measures at using a safety pillow, thus address to subsection the Steering.


2. Remove the block of a pillow of safety from outside the driver, thus address to subsection Removal and installation of the block of a pillow of safety.
3. Remove a steering wheel, thus address to subsection Removal and steering wheel installation.
4. Disconnect the handle of the mechanism of adjustment of a steering column–1.
5. Turn out 2 screws with crosswise шлицем–4 and the screw with internal шестигранником–2 (a key of 4 mm).
6. Turn out 2 screws of fastening by-3 thin long screw-driver.
7. Remove the top and bottom parts facing подрулевого the switch.
8. Расстыкуйте a socket–1.
9. Turn away the screw with internal шестигранником–2 (5 mm) so that подрулевой the switch could move slightly.
10. Cautiously disconnect electric connections from подрулевого the switch.
ATTENTION

At removal подрулевого the switch the spring remains on the switch. Watch that the spring was not braided and remained in the average position.


11. Remove подрулевой the switch from a column and put aside.

INSTALLATION

PERFORMANCE ORDER
1. Put on подрулевой the switch–2 a steering column, without fixing it.
2. Put on a steering wheel.
3. Fix at first подрулевой the switch–2 screw with internal шестигранником–3 on a steering column so that the distance to a steering wheel made and = 3 mm.
4. Again remove a steering wheel and execute the further installation in sequence, return to removal.
5. Establish a steering wheel, address to subsection Removal and steering wheel installation.
6. Establish a safety pillow, address to subsection Removal and installation of the block of a pillow of safety.
7. Attach a weight cable (–) the storage battery. Attention: Make active high-rise automatics electric window lifterа, and also establish hours and enter a radio tape recorder code, address to subsection Input of a code of a radio receiver.
On the main page