Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
- 11. Brake system
   11.1. A technical characteristics
   + 11.2. Prorolling of hydraulic brake system
   11.3. Brake pipelines and hoses
   + 11.4. Lobbies brake Pads
   11.5. Replacement back brake колодок on disk brakes
   11.6. Replacement back brake колодок on drum-type brakes
   11.7. Check, removal and installation of a forward brake disk
   11.8. Check, removal and installation of a back brake disk
   11.9. Removal, check and installation of a brake drum
   + 11.10. A support of a forward brake
   + 11.11. A support of a back disk brake
   + 11.12. The back working brake cylinder
   - 11.13. The main brake cylinder
      11.13.1. Removal and installation of the main brake cylinder
      - 11.13.2. Repair of the main brake cylinder (model without ABS)
         11.13.2.1. The main brake cylinder of type АТЕ
         11.13.2.2. The main brake cylinder of type GMF
   + 11.14. Valves of adjustment of pressure
   11.15. Replacement of the unidirectional valve of the vacuum amplifier of brakes
   11.16. Check, removal and installation of the vacuum amplifier of brakes
   11.17. Removal and installation of a pedal of a brake
   11.18. Removal and installation of a cable of a manual brake
   11.19. Removal and installation of the lever of a manual brake
   11.20. Replacement brake колодок a manual brake on back disk brakes
   + 11.21. Antiblocking system of brakes (ABS)
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes





11.13.2.2. The main brake cylinder of type GMF
THE GENERAL DATA

The main brake cylinder of type GMF
1 – the cylinder,
2 – consolidation пополнительного a tank,
3 – скобы fastenings пополнительного a tank,
4 – пополнительный a tank,
5 – a cover пополнительного a tank
(With the gauge of level of a brake liquid),
7 – a spring,
8 – an emphasis of a spring,
9 – a sealing ring secondary
The piston,

10 – a restrictive washer,
11 – the secondary piston,
12 – a sealing ring
The primary piston,
13 – a lock ring,
14 – the plug of a spring,
15 – a spring,
16 – an emphasis of a spring,
17 – the primary piston,
18 – a lock ring


PERFORMANCE ORDER
1. Remove the main brake cylinder.
2. Fix the main brake cylinder in a vice with soft sponges.
3. At presence unscrew valves of adjustment of pressure from the basis of the main brake cylinder.
4. Using a screw-driver edge as the lever, remove from an end face of the main brake cylinder a sealing ring.
5. A wooden or plastic stick press the primary piston into the main brake cylinder and in this position of the piston insert a steel core in diameter of 3 mm through an aperture of installation of a nutritious tank into the main brake cylinder.
6. Take a lock ring from the channel of the main brake cylinder.
7. Take a steel core in diameter of 3 mm, fixing piston in the pressed position.
8. Take the primary piston from the main brake cylinder for what turn the main brake cylinder and knock with it about a board.
9. Submit to the main brake cylinder air under low pressure through an aperture for installation of a nutritious tank and squeeze out the secondary piston from the main brake cylinder.
10. Clear all details of the main brake cylinder in a pure brake liquid or methyl spirit and check up their condition.
11. Check up pistons and the cylinder channel on presence of scratches and dot corrosion.
12. At deterioration of the cylinder replace the main brake cylinder in gathering.
13. Grease the cylinder channel with a thin layer of a pure brake liquid, then fix the cylinder in horizontal position in a vice with soft sponges.
14. Using details of the repair complete set, remove a stopper from the end of an auxiliary tube and insert a short part of a tube into the channel of the main brake cylinder.
15. Using a wooden or plastic stick, push out the repair complete set of details from a tube in the channel of the main brake cylinder.
16. A stick press the primary piston and, using a steel midstream in diameter of 3 mm fix the piston in the pressed position.
17. Establish a new lock ring in the cylinder channel. Check up that the lock ring was accurately established in a flute of the cylinder and the piston freely moves in the cylinder.
18. Press the primary piston and take the steel core keeping the piston in pressed position.
19. Establish a new sealing ring on an end face of the main brake cylinder.
20. At presence screw in valves of adjustment of pressure.
21. Establish the main brake cylinder.

On the main page