Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
- 4. The engine
   + 4.1. Engine OHV (with a camshaft in the block of cylinders)
   + 4.2. Engines OHC
   + 4.3. Engine DOHC with 16 valves
   - 4.4. Diesel engines 16D and 16DА
      4.4.1. A technical characteristics
      4.4.2. A method of removal of the engine
      4.4.3. Engine repair
      4.4.4. Replacement of engine oil and the oil filter
      4.4.5. Check, removal, installation and adjustment of a gear belt
      + 4.4.6. A mechanism drive timing
      4.4.7. Removal and installation of a head of the block of cylinders
      4.4.8. Removal and camshaft installation
      4.4.9. Removal and installation of the oil pallet
      4.4.10. Removal and installation of the oil pump
      4.4.11. Removal and installation перепускного the valve
      4.4.12. Removal and installation of the water pump
      4.4.13. Removal, check and thermostat installation
      4.4.14. Removal and installation of pistons and rods
      4.4.15. Removal and flywheel installation
      + 4.4.16. Replacement of sealing rings
      4.4.17. Replacement of support of the power unit
      + 4.4.18. Removal of the engine from a transmission
      4.4.19. Engine and transmission division
      4.4.20. Engine repair
      4.4.21. Removal, repair and assemblage of the oil pump
      + 4.4.22. A head of the block of cylinders
      4.4.23. Check and restoration of details of the engine
      + 4.4.24. Check of elements of the engine
      4.4.25. Replacement of pushers, persistent linings and hydraulic pushers
      4.4.26. Engine assemblage.
      4.4.27. Connection of the engine with a transmission
      4.4.28. Engine and transmission installation
   + 4.5. Diesel engines of 1,7 l
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes





4.4.25. Replacement of pushers, persistent linings and hydraulic pushers
THE GENERAL DATA

HYDRAULIC PUSHERS

Details of a hydraulic pusher of valves

1 – a ring,
2 – плунжер,
3 – a ball,
4 – a spring,
5 – a cover,
6 – a spring,
7 – the cylinder

If hydraulic pushers of valves are worn out, it is necessary to replace them.

To lower probability of occurrence of problems in the future, it is recommended to assort and clean hydraulic pushers each time when you remove a head of cylinders.

PERFORMANCE ORDER
1. Since a pusher of the valve of the first cylinder, remove a ring from the top part of the cylinder of a pusher.
2. Take from the cylinder the piston and a spring.
3. A small screw-driver remove a cap in the piston basis. Get пружинку (1) and a ball (2) from under a cap.
4. Carefully wash out elements of a pusher kerosene. If pusher springs are worn out or damaged, replace a pusher entirely.
5. Pusher assemblage is made in sequence, return dismantling.
6. Establish a ball (1) in an aperture (2).
7. Establish a cap.
8. Establish a spring on a cap.
9. Insert the piston and a spring into the cylinder.
10. Put on a ring (1) the top part of the piston and an edge of the cylinder (2).

PUSHERS AND PERSISTENT LININGS OF VALVES

Examine pushers and linings on presence of deterioration and damages and replace them if necessary.

TECHNOLOGICAL ЗАГЛУШКИ

Removal заглушек


PERFORMANCE ORDER
Examine заглушки in a head and the block of cylinders. If necessary replace заглушки.

On the main page