Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
- 6. Fuel and exhaust systems
   - 6.1. Models with the carburettor
      6.1.1. A technical characteristics
      6.1.2. Use unleaded gasoline
      6.1.3. Removal and installation of the case of the air filter
      6.1.4. System of adjustment of temperature of air arriving in the engine
      6.1.5. Check, removal and installation of the fuel pump
      6.1.6. Removal and installation of the gauge of level of fuel
      6.1.7. Removal and installation of a fuel tank
      6.1.8. Removal, installation and adjustment of a cable of an accelerator
      6.1.9. Removal and installation of a pedal of an accelerator
      6.1.10. Removal, installation and adjustment of a cable of management air заслонкой
      - 6.1.11. Carburettors
         + 6.1.11.1. Adjustments on the carburettor 32 TL
         + 6.1.11.2. Adjustments on the carburettor 35 PDSI
         - 6.1.11.3. Adjustments on the carburettor 1В1
            6.1.11.3.1. Turns of idling and quality of a fuel mix
            6.1.11.3.2. The accelerated turns of idling
            6.1.11.3.3. A block cover заслонки
            6.1.11.3.4. A vacuum diaphragm throttle заслонки the secondary chamber
            6.1.11.3.5. A backlash air заслонки
            6.1.11.3.6. The basic adjustment throttle заслонки
            6.1.11.3.7. Productivity of the accelerating pump
         + 6.1.11.4. Adjustments on the carburettor 2Е3
         + 6.1.11.5. Adjustments on carburettor Varajei II
      6.1.12. Check of the electromagnetic valve of a stopping delivery of fuel
      6.1.13. Removal and carburettor installation
      + 6.1.14. Carburettor repair
      6.1.15. Removal and installation of an inlet collector
      6.1.16. Removal and installation of a final collector
      6.1.17. Removal and installation of a heater of an inlet collector
      6.1.18. Removal and exhaust system installation
   + 6.2. Models with system of injection of fuel
   + 6.3. Models with engines 16D and 16DA
   + 6.4. Models with engines 17D and 17DR
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes

6.1.11.3.5. A backlash air заслонки
PERFORMANCE ORDER
1. Start the engine and warm up it to normal working temperature, then switch off the engine and remove the air filter.
2. Extend the handle of management air заслонкой against the stop and check up that draught has turned in completely closed position against the stop the lever. If necessary adjust a cable of management air заслонкой.
3. With completely extended handle of management air заслонкой start the engine and check up that between air заслонкой and диффузором it is possible to insert a shaft of a drill in diameter resulted in subsection 6.1.1.
4. If necessary ослабьте a counternut and, rotating the adjusting screw (it is specified by an arrow), located over the vacuum chamber, adjust a backlash.
5. Switch off the engine, tighten a counternut and establish the air filter.


On the main page