Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
- 6. Fuel and exhaust systems
   - 6.1. Models with the carburettor
      6.1.1. A technical characteristics
      6.1.2. Use unleaded gasoline
      6.1.3. Removal and installation of the case of the air filter
      6.1.4. System of adjustment of temperature of air arriving in the engine
      6.1.5. Check, removal and installation of the fuel pump
      6.1.6. Removal and installation of the gauge of level of fuel
      6.1.7. Removal and installation of a fuel tank
      6.1.8. Removal, installation and adjustment of a cable of an accelerator
      6.1.9. Removal and installation of a pedal of an accelerator
      6.1.10. Removal, installation and adjustment of a cable of management air заслонкой
      - 6.1.11. Carburettors
         + 6.1.11.1. Adjustments on the carburettor 32 TL
         + 6.1.11.2. Adjustments on the carburettor 35 PDSI
         - 6.1.11.3. Adjustments on the carburettor 1В1
            6.1.11.3.1. Turns of idling and quality of a fuel mix
            6.1.11.3.2. The accelerated turns of idling
            6.1.11.3.3. A block cover заслонки
            6.1.11.3.4. A vacuum diaphragm throttle заслонки the secondary chamber
            6.1.11.3.5. A backlash air заслонки
            6.1.11.3.6. The basic adjustment throttle заслонки
            6.1.11.3.7. Productivity of the accelerating pump
         + 6.1.11.4. Adjustments on the carburettor 2Е3
         + 6.1.11.5. Adjustments on carburettor Varajei II
      6.1.12. Check of the electromagnetic valve of a stopping delivery of fuel
      6.1.13. Removal and carburettor installation
      + 6.1.14. Carburettor repair
      6.1.15. Removal and installation of an inlet collector
      6.1.16. Removal and installation of a final collector
      6.1.17. Removal and installation of a heater of an inlet collector
      6.1.18. Removal and exhaust system installation
   + 6.2. Models with system of injection of fuel
   + 6.3. Models with engines 16D and 16DA
   + 6.4. Models with engines 17D and 17DR
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes





6.1.11.3.7. Productivity of the accelerating pump
PERFORMANCE ORDER
1. Remove the air filter, then start the engine for some seconds, then switch off it. Looking from above in the carburettor, open manually throttle заслонку. At opening throttle заслонки the double stream of fuel submitted from a spray of the accelerating pump should be observed. In the absence of a fuel stream execute check as follows.
2. At check of working capacity of the accelerating pump it is necessary in поплавковую to submit the chamber fuel from the additional tank.
3. Establish the primary chamber of the carburettor over a volumetric glass. Ten times completely open and close throttle заслонку, and opening заслонки make within 1 second then return заслонку in a starting position and in 3 seconds repeatedly open it. Check up, that the cam of the accelerated turns of idling did not limit moving throttle заслонки.
4. Measure quantity of fuel which the accelerating pump has submitted to a volumetric glass, and compare this data with resulted in subsection 6.1.1.
5. If adjustment is required, ослабьте the screw of fastening and turn a cam in a demanded direction then tighten the screw and repeatedly check up productivity of the accelerating pump.
6. For adjustment ослабьте the screw (under an arrow) also turn a cam plate in a demanded direction.

On the main page