Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
- Routine maintenance
The schedule of routine maintenance of cars Subaru Legacy and Outback
Specifications
The general data on options and adjustments
Check of levels of liquids (according to the routine maintenance Schedule)
Replacement of impellent oil and the oil filter
Check of a condition and replacement of the hoses located in an impellent compartment
Rotation of wheels
Greasing of components of the chassis
Check of a condition of components of system of release of the fulfilled gases
Check of a condition of seat belts
Check of a condition of components of a suspension bracket
Check of a condition of components of a steering drive
Check and adjustment of structure of a mix of idling, - to a forage of the models equipped catalytic with the converter
Check of a condition of protective covers of hinges of power shafts
Condition check, adjustment of effort of a tension of belts of a drive of auxiliary units
Check and adjustment противооткатного devices
Check of serviceability of functioning and adjustment of components of coupling
Checks and adjustments of brake system
Check of a condition of components of system of cooling
Check of a condition and replacement of a cooling liquid of the engine
Replacement of a filtering element of an air cleaner
Check of a condition of components of the power supply system
Replacement of a brake liquid/prorolling of a hydraulic path
Replacement ATF of automatic transmission
Replacement трансмиссионного oils РКПП
Replacement of greasings of back and forward differential
Check of a condition and replacement газораспределительного a belt - models 2.0 and 2.5 l
Check and replacement of the fuel filter
Check of a condition and replacement of spark plugs and ВВ electroconductings
Check of wheel bearings
Check клапанных backlashes
Replacement of belts of a drive of auxiliary units and replacement
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Check of a condition of components of a suspension bracket
|
The condition of components of a suspension bracket and steering drive should be made regularly as their deterioration or damage can be at the bottom of reduction of service life of tyres, conduct to decrease in controllability of the car and increase of the expense of fuel. The detailed illustrative material is presented also in the Head the Suspension bracket and a steering. |
The checks made without a separation of wheels from the earth
|
1. Park the car on an equal horizontal platform, whenever possible with a firm covering, develop forward wheels in rectilinear position. Slightly pull a steering wheel in both directions, - the excessive size taking place люфта specifies in possible deterioration of wheel bearings, collars of hinges of shaft of a steering column, bearings of rotary fists, or tips of steering draughts. The probability of infringement of adjustment or damage of components реечной transfers (the Suspension bracket and a steering see the Head) is not excluded also.
2. In deterioration or damage of components of a suspension bracket or a steering drive can specify also such symptoms, as excessive rocking of the car at movement on rough road or during fulfilment of turns, steering wheel jammings, etc. 3. For an estimation of a condition of shock-absorbers press downwards one of car corners. At release a corner the body should come back in a starting position, making no more than one-two fluctuations. Listen to a scratch and the other extraneous noise published by a suspension bracket at oscillative motions of a body. Excessive quantity раскачиваний bodies at release a corner, no less than refusal of its return to a starting position, testify to necessity of replacement of shock-absorbers. Operating in a similar manner, serially check up each of four shock-absorbers. |
|
Check of height of position of wheel arches
|
1. Unload from the car all luggage and leave it completely filled and equipped.
2. Check up height of wheel arches (the Suspension bracket and a steering see the Head), compare results of measurements to requirements of Specifications.
3. If the height of an arch of a wheel does not correspond to specifications, check up a condition of components suspension brackets (racks/shock-absorbers) and кузовных elements to which they fasten. Replace defective components.
4. In the absence of the deformed components adjust height of arches by replacement of corresponding screw springs of a suspension bracket.
|
|
Check of corners of installation of forward wheels
|
1. Check up geometry of a forward suspension bracket and make sure of conformity to the accepted norms of corners of installation of wheels (convergence, disorder, a corner of a longitudinal inclination of an axis of turn of a wheel [выбег], angles of rotation of wheels). 2. If the corner of a longitudinal inclination of an axis of turn of a wheel does not correspond to standard value, visually estimate a condition of components of a suspension bracket (assemblage of forward racks, a cross-section beam, cross-section levers and so forth) and кузовных elements to which they fasten. Replace defective components. 3. If convergence and disorder do not correspond to standard values, make corresponding adjustments (the Suspension bracket and a steering see the Head).
4. If the left and right angles of rotation of wheels do not correspond to standard values, make corresponding adjustments (the Suspension bracket and a steering see the Head). |
|
Check of corners of installation of back wheels
|
1. Check up geometry of a forward suspension bracket and make sure of conformity to the accepted norms of corners of installation of wheels (convergence, disorder, a corner of a course deviation). 2. If the disorder corner does not correspond to standard value, visually estimate a condition of components of a suspension bracket (draught [forward, back and top], the back lever, a stretcher, shock-absorbers and so forth) and кузовных elements to which they fasten. Replace defective components. 3. If convergence and a corner of a course deviation do not correspond to standard values, make corresponding adjustments (the Suspension bracket and a steering see the Head). |
|
The checks made with a separation of wheels from the earth
|
In regions where in the winter to snow thawing on roads apply salt, check elements of a suspension bracket about corrosion development each 12 months after the expiration of 60 months from the moment of the operation beginning. If it is necessary, apply measures on prevention of occurrence of corrosion. |
|
1. Поддомкратьте the car also establish it on props. 2. Check up protectors of wheels on presence of traces of non-uniform deterioration, estimate pressure of a rating of tyres.
|
3. Address to materials of the Head the Suspension bracket and a steering. Estimate a condition карданных hinges of a steering column. Check up protective covers of the steering mechanism and power shafts on presence of signs of leaks of greasing. Check up reliability of landing of tips of steering draughts. Check up a condition of all components of a suspension bracket and reliability of a tightening of their fixture. After отдавания самоконтрящихся nuts and bolts, replace their new. Estimate degree of deterioration of rubber components of a suspension bracket and a steering drive. Check up маслозаполненные plugs of levers of a suspension bracket on presence of signs of leaks, in case of need make replacement. Ask the assistant повращать a steering wheel and visually estimate size люфта a steering drive. Try to establish the reason of a taking place weak point, make necessary regenerative repair, or replace defective components. |
4. Manually rotating forward wheels, try to define on hearing a condition of wheel bearings, make sure of absence люфта at rotation of wheels. Grasp a wheel in points on 12 and at 6 o'clock and pull it in an axial plane, - presence some an appreciable free wheeling testifies to easing of a pretightness of wheel bearings. 5. Hooking components mount, estimate a condition of bearings of assemblages of rotary fists. In case of revealing люфта it is necessary to subject bearings to more detailed studying, to make replacement or stuffing by their fresh greasing.
6. Estimate degree of deterioration of universal hinges and sliding муфт карданных shaft (Coupling see the Head).
7. Examine surfaces картеров transmissions on presence of signs of development of leaks. |
|
Check of a condition of spherical support of cross-section levers of a suspension bracket
|
|
1. Grasp a bottom edge of a wheel and pull it forward-back, - presence люфта a brake board concerning the cross-section lever of a suspension bracket, testifies to excessive deterioration of a spherical support. |
|
2. Grasp the end of the cross-section lever and pull it upwards-downwards, - presence люфта the lever concerning a rotary fist also specifies in necessity of careful check of a condition of a spherical support. |
3. At negative results of both checks remove a spherical support (the Suspension bracket and a steering see a disk 2 the Head) and measure size of a free wheeling of a spherical finger (the Suspension bracket and a steering see the Head). Compare result of measurement to requirements of Specifications, in case of need replace spherical support (better in the complete set).
|
4. Visually estimate a condition dusterа a spherical support. At revealing of mechanical damages, remove the cross-section lever and measure size of a free wheeling of its finger (the Suspension bracket and a steering see the Head). Compare result of measurement to requirements of Specifications, in case of need replace spherical support (better in the complete set).
|
After removal or replacement of a spherical support it is necessary to check up size of a convergence of forward wheels, - in case of need make corresponding updating. |
|
5. Check of a condition a clod-ponentov steering privo-yes (each 25 000 km [15 000 miles] run or times in 12 months) |
|
|
On the main page
|