Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
- Routine maintenance
   The schedule of routine maintenance of cars Subaru Legacy and Outback
   Specifications
   The general data on options and adjustments
   Check of levels of liquids (according to the routine maintenance Schedule)
   Replacement of impellent oil and the oil filter
   Check of a condition and replacement of the hoses located in an impellent compartment
   Rotation of wheels
   Greasing of components of the chassis
   Check of a condition of components of system of release of the fulfilled gases
   Check of a condition of seat belts
   Check of a condition of components of a suspension bracket
   Check of a condition of components of a steering drive
   Check and adjustment of structure of a mix of idling, - to a forage of the models equipped catalytic with the converter
   Check of a condition of protective covers of hinges of power shafts
   Condition check, adjustment of effort of a tension of belts of a drive of auxiliary units
   Check and adjustment противооткатного devices
   Check of serviceability of functioning and adjustment of components of coupling
   Checks and adjustments of brake system
   Check of a condition of components of system of cooling
   Check of a condition and replacement of a cooling liquid of the engine
   Replacement of a filtering element of an air cleaner
   Check of a condition of components of the power supply system
   Replacement of a brake liquid/prorolling of a hydraulic path
   Replacement ATF of automatic transmission
   Replacement трансмиссионного oils РКПП
   Replacement of greasings of back and forward differential
   Check of a condition and replacement газораспределительного a belt - models 2.0 and 2.5 l
   Check and replacement of the fuel filter
   Check of a condition and replacement of spark plugs and ВВ electroconductings
   Check of wheel bearings
   Check клапанных backlashes
   Replacement of belts of a drive of auxiliary units and replacement
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Check of a condition and replacement газораспределительного a belt - models 2.0 and 2.5 l

Installation details газораспределительного a belt

1 — the Right back cover of drive ГРМ
2 — Directing газораспределительного a belt (only models with РКПП)
3 — the Cogwheel of a cranked shaft
4 — the Left back cover of drive ГРМ
5 — the Cogwheel of the right camshaft
6 — the Intermediate roller № 1
7 — the Basic arm натяжителя
8 — the Intermediate roller № 2

9 — Assemblage automatic натяжителя
10 — the Gear intermediate roller № 2
11 — the Cogwheel of the left camshaft
12 — Gazoraspredelitelnyj a belt
13 — the Right forward cover of drive ГРМ
14 — the Left forward cover of drive ГРМ
15 — the Pulley of a cranked shaft (model 2.0)
16 — the Pulley of a cranked shaft (model 2.5)

CHECK

 PERFORMANCE ORDER

1. Muffle the engine, open a cowl and remove the left and right forward covers of drive ГРМ.
2. Highlighting itself a small lamp, fingers feel a belt on all length, checking it on presence of cracks and stratifications. Presence on a belt of attritions, заполированных to shine of sites and other obvious defects is inadmissible also. If necessary replace the damaged belt.

3. Measure width of a tape газораспределительного a belt. If the result of measurement makes less than 27 mm, check up perpendicularity of installation and correctness of combination of intermediate rollers and cogwheels of drive ГРМ, in case of need make necessary corrections/replacements. Replace worn out газораспределительный a belt.

4. Establish to the place of a cover of drive ГРМ.

REPLACEMENT

 PERFORMANCE ORDER

1. Remove fans of systems of cooling of the engine and an air conditioning (see the Head of System of cooling, heating).

2. Remove a protective casing of belts of a drive of auxiliary units.

3. Remove V-shaped приводные belts.
4. At a corresponding complete set remove натяжитель a belt of a drive of compressor K/V.

5. Turn out a bolt of fastening of a pulley of a cranked shaft, - for blocking of a shaft from проворачивания take advantage of special key ST 499977100. Remove a pulley.

6. Remove at first left, then right sections of a forward cover of drive ГРМ. Then remove a casing of the belt located in front.

7. On models with РКПП turn out fixing bolts and remove directing газораспределительного a belt.

8. Turning a cranked shaft by means of head ST 499987500, achieve combination of adjusting labels of cogwheels cranked and both camshafts with reciprocal risks on a back cover/block of cylinders.

9. Remove intermediate rollers.

10. Remove a belt of drive ГРМ.

11. Remove assemblage of an automatic regulator of a tension of a belt.

12. At purchase of new belts take with itself old as samples - replaceable belts should correspond strictly removed from the car on a standard size.

INSTALLATION

 PERFORMANCE ORDER

1. Establish a new belt of drive ГРМ, - track for correctness of combination of adjusting labels.

 Infringement of installation of phases timing is fraught with damage of internal components of the engine as a result of blow of valves about the bottoms of pistons!

2. The further installation is made as it should be the return to an order of dismantle of components.


On the main page