Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
- Routine maintenance
   The schedule of routine maintenance of cars Subaru Legacy and Outback
   Specifications
   The general data on options and adjustments
   Check of levels of liquids (according to the routine maintenance Schedule)
   Replacement of impellent oil and the oil filter
   Check of a condition and replacement of the hoses located in an impellent compartment
   Rotation of wheels
   Greasing of components of the chassis
   Check of a condition of components of system of release of the fulfilled gases
   Check of a condition of seat belts
   Check of a condition of components of a suspension bracket
   Check of a condition of components of a steering drive
   Check and adjustment of structure of a mix of idling, - to a forage of the models equipped catalytic with the converter
   Check of a condition of protective covers of hinges of power shafts
   Condition check, adjustment of effort of a tension of belts of a drive of auxiliary units
   Check and adjustment противооткатного devices
   Check of serviceability of functioning and adjustment of components of coupling
   Checks and adjustments of brake system
   Check of a condition of components of system of cooling
   Check of a condition and replacement of a cooling liquid of the engine
   Replacement of a filtering element of an air cleaner
   Check of a condition of components of the power supply system
   Replacement of a brake liquid/prorolling of a hydraulic path
   Replacement ATF of automatic transmission
   Replacement трансмиссионного oils РКПП
   Replacement of greasings of back and forward differential
   Check of a condition and replacement газораспределительного a belt - models 2.0 and 2.5 l
   Check and replacement of the fuel filter
   Check of a condition and replacement of spark plugs and ВВ electroconductings
   Check of wheel bearings
   Check клапанных backlashes
   Replacement of belts of a drive of auxiliary units and replacement
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Replacement of a brake liquid/prorolling of a hydraulic path

Sequence of prorolling

1 — the Brake mechanism of the right forward wheel
2 — the Brake mechanism of the left back wheel
3 — the Brake mechanism of the left forward wheel

4 — the Brake mechanism of the right back wheel
5 — Secondary chamber GTTS
6 — Primary chamber GTTS


 PERFORMANCE ORDER

 For performance of the given procedure the help of the assistant is required, or it is necessary to get a special set for prorolling of brake system by forces of one person - ask in shops of automobile accessories.

1. Поддомкратьте the car also establish it on props.
2. Remove all wheels.
3. By means of a syringe or a rubber pear pump out a brake liquid from the tank of the main brake cylinder (ГТЦ).
4. Fill in in the tank a fresh brake liquid of a demanded grade, - try not to admit hit in a brake path of a dirt.

 Mixing of hydraulic liquids of a various grade is fraught with dangerous decrease in efficiency of functioning of brake system!

5. Connect one end of a vinyl tube of suitable diameter to the gate of prorolling of a support of the brake mechanism of the right forward wheel, the second end of a tube lower in drain capacity of the adequate size.

 In order to avoid hit of a brake liquid on components of the brake mechanism, before отпусканием wrap up the drain gate old rags.

6. Ask the assistant 2-3 times to press slowly a brake pedal, then to fix it in the squeezed out position.
7. Release the prorolling gate approximately on 1/4 turns and let out a small amount of a hydraulic liquid in drain capacity, then again tighten the gate.
8. Continue to operate in the manner described in two previous paragraphs until the pure, transparent, free liquid will not start to follow from a tube from air bubbles.

 Do not forget to watch liquid level in tank GTTS, without supposing its excessive lowering, - during time add a fresh liquid!

9. Having finished prorolling, tighten the gate with demanded effort at the pressed pedal of a foot brake.
10. Operating in a similar manner, in strictly certain order consistently pump over brake mechanisms of the remained wheels and both chambers GTTS.
11. In summary, squeeze out a pedal of a foot brake with effort approximately 30 кГс and, keeping its 20 seconds pressed during an order, make sure of absence excessive люфта pedals, then examine gates of prorolling of brake mechanisms, ГТЦ and all штуцерные sockets of a hydraulic path on presence of signs of development of leaks. In case of need make corresponding corrections/replace defective components.
12. Establish to the place of a wheel, lower the car on the earth during short (2-3 km) trips check up serviceability of functioning of brake system.


On the main page