Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
- 6. Fuel and exhaust systems
   - 6.1. Models with the carburettor
      6.1.1. A technical characteristics
      6.1.2. Use unleaded gasoline
      6.1.3. Removal and installation of the case of the air filter
      6.1.4. System of adjustment of temperature of air arriving in the engine
      6.1.5. Check, removal and installation of the fuel pump
      6.1.6. Removal and installation of the gauge of level of fuel
      6.1.7. Removal and installation of a fuel tank
      6.1.8. Removal, installation and adjustment of a cable of an accelerator
      6.1.9. Removal and installation of a pedal of an accelerator
      6.1.10. Removal, installation and adjustment of a cable of management air заслонкой
      - 6.1.11. Carburettors
         + 6.1.11.1. Adjustments on the carburettor 32 TL
         + 6.1.11.2. Adjustments on the carburettor 35 PDSI
         + 6.1.11.3. Adjustments on the carburettor 1В1
         + 6.1.11.4. Adjustments on the carburettor 2Е3
         - 6.1.11.5. Adjustments on carburettor Varajei II
            - 6.1.11.5.1. The carburettor with automatic air заслонкой
               6.1.11.5.1.1. Turns of idling and quality of a fuel mix
               6.1.11.5.1.2. The accelerated turns of idling
               6.1.11.5.1.3. Заслонка movings (backlash)
               6.1.11.5.1.4. The accelerated idling (backlash)
               6.1.11.5.1.5. Position completely open throttle заслонки
               6.1.11.5.1.6. A cover automatic air заслонки
               6.1.11.5.1.7. The accelerating pump
               6.1.11.5.1.8. The shock-absorber throttle заслонки
               6.1.11.5.1.9. Partial loading
            + 6.1.11.5.2. The hand-operated carburettor air заслонкой
      6.1.12. Check of the electromagnetic valve of a stopping delivery of fuel
      6.1.13. Removal and carburettor installation
      + 6.1.14. Carburettor repair
      6.1.15. Removal and installation of an inlet collector
      6.1.16. Removal and installation of a final collector
      6.1.17. Removal and installation of a heater of an inlet collector
      6.1.18. Removal and exhaust system installation
   + 6.2. Models with system of injection of fuel
   + 6.3. Models with engines 16D and 16DA
   + 6.4. Models with engines 17D and 17DR
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes





6.1.11.5.1.3. Заслонка movings (backlash)
THE GENERAL DATA

For performance of this operation it is necessary to use the vacuum pump.

PERFORMANCE ORDER
1. Remove the air filter.
2. Establish the screw of adjustment of the accelerated turns of idling on the top step of a cam. Check up that air заслонка it is completely closed. Otherwise, if заслонка still warm, it is necessary to use an elastic band for deduction заслонки in the closed position.
3. Create vacuum in the vacuum chamber заслонки.
4. Using a drill shaft, measure a backlash between air заслонкой and a wall диффузора.
5. The backlash () should correspond to the requirements resulted in subsection 6.1.1 (In – the adjusting screw).
6. If necessary, rotating the adjusting screw In, establish a demanded backlash. If a backlash too small, it is necessary to bend draught for maintenance sufficient люфта for a course of the adjusting screw.
7. After adjustment fix the screw, having put on its carving hermetic.
8. Check up a free wheeling between a control lever flaps дефлектора and draught of the vacuum block. Thus draught should be established in final position (And = 0,1–0,3 mm). If necessary turn in the end of draught for backlash installation in demanded limits.

On the main page