Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
+ 4. The engine
+ 5. System of cooling, heating and ventilation
- 6. Fuel and exhaust systems
   - 6.1. Models with the carburettor
      6.1.1. A technical characteristics
      6.1.2. Use unleaded gasoline
      6.1.3. Removal and installation of the case of the air filter
      6.1.4. System of adjustment of temperature of air arriving in the engine
      6.1.5. Check, removal and installation of the fuel pump
      6.1.6. Removal and installation of the gauge of level of fuel
      6.1.7. Removal and installation of a fuel tank
      6.1.8. Removal, installation and adjustment of a cable of an accelerator
      6.1.9. Removal and installation of a pedal of an accelerator
      6.1.10. Removal, installation and adjustment of a cable of management air заслонкой
      - 6.1.11. Carburettors
         + 6.1.11.1. Adjustments on the carburettor 32 TL
         + 6.1.11.2. Adjustments on the carburettor 35 PDSI
         + 6.1.11.3. Adjustments on the carburettor 1В1
         + 6.1.11.4. Adjustments on the carburettor 2Е3
         - 6.1.11.5. Adjustments on carburettor Varajei II
            - 6.1.11.5.1. The carburettor with automatic air заслонкой
               6.1.11.5.1.1. Turns of idling and quality of a fuel mix
               6.1.11.5.1.2. The accelerated turns of idling
               6.1.11.5.1.3. Заслонка movings (backlash)
               6.1.11.5.1.4. The accelerated idling (backlash)
               6.1.11.5.1.5. Position completely open throttle заслонки
               6.1.11.5.1.6. A cover automatic air заслонки
               6.1.11.5.1.7. The accelerating pump
               6.1.11.5.1.8. The shock-absorber throttle заслонки
               6.1.11.5.1.9. Partial loading
            + 6.1.11.5.2. The hand-operated carburettor air заслонкой
      6.1.12. Check of the electromagnetic valve of a stopping delivery of fuel
      6.1.13. Removal and carburettor installation
      + 6.1.14. Carburettor repair
      6.1.15. Removal and installation of an inlet collector
      6.1.16. Removal and installation of a final collector
      6.1.17. Removal and installation of a heater of an inlet collector
      6.1.18. Removal and exhaust system installation
   + 6.2. Models with system of injection of fuel
   + 6.3. Models with engines 16D and 16DA
   + 6.4. Models with engines 17D and 17DR
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes





6.1.11.5.1.4. The accelerated idling (backlash)
PERFORMANCE ORDER
1. Close air заслонку and fix it in this position by an elastic band.
2. Open throttle заслонку and establish the screw of the accelerated turns of idling on the second step of a cam. Release throttle заслонку and check up that the screw remained on a place.
3. Slightly slightly open, and then release air заслонку that it was established in correct position. Check up a backlash air заслонки In the same method, as at check of a backlash of moving in the bottom part throttle заслонки. Backlash B should correspond to the requirements resulted in subsection 6.1.1.
4. If it is necessary to make adjustment, remove the carburettor and a cover заслонки. Turn in draught which connects a cam of the accelerated turns of idling to the lever air заслонки, before reception of a demanded backlash.
5. After adjustment repeatedly check up a backlash In the ambassador of installation of the carburettor on the engine.

On the main page