Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
- Manual box and differential
   Specifications
   The mechanism of blocking of inclusion of a reverse gear - the device and a functioning principle
   Interaxal differential - the device and a functioning principle
   Removal and installation трансмиссионной assemblages
   Check of a condition and replacement of elements of support of a suspension bracket трансмиссионной assemblages
   Check of a condition and epiploon replacement
   Removal, installation and check of a condition of gauges-switches
   Removal, installation and check of a condition of the gauge of speed (VSS)
   Preparation for performance of major repairs РКПП
   Removal, service and installation of a distributing box and transmission lengthening
   Removal, service and installation of a leading gear wheel of the distributing mechanism
   Removal, service and installation of a conducted gear wheel of the distributing mechanism
   Removal, service and installation of interaxal differential
   Removal, service, installation and adjustment of assemblage of the mechanism of blocking of inclusion of a reverse gear
   Removal, installation and condition check картера трансмиссионной assemblages
   Removal, service, installation and adjustment of primary shaft РКПП
   Removal, service and installation of entrance shaft РКПП (models with an additional two-level reducer)
   Removal, service and installation of assemblage of a shaft of a leading gear wheel of the main transfer of a drive of forward wheels
   Removal, service, installation and adjustment of forward differential
   Removal, installation and check of a condition of a gear wheel of a drive of a speedometer
   Removal, installation and adjustment of an intermediate gear wheel of a reverse gear
   Removal, installation, check and adjustment of assemblage of gear wheels of a two-level reducer
   Removal, check of a condition and installation of plugs and gear change rods
   Removal, service and installation of the lever of gear change РКПП
   Removal, service and installation of the lever of switching of modes «Hi/Lo» an additional two-level reducer
   Removal, service and installation тросовой draughts of a drive of switching of modes of a two-level reducer
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal, service and installation тросовой draughts of a drive of switching of modes of a two-level reducer

REMOVAL

 PERFORMANCE ORDER

1. Remove the lever of switching of modes (see Has undressed Removal, service and installation of the lever of switching of modes «Hi/Lo» an additional two-level reducer).
2. Remove the case of an air cleaner with an air inlet sleeve (see the Head of the Power supply system and release).

3. Remove a spring lock ring and take a fastening pin тросовой draughts.

And — the Spring lock ring
In — the Pin
With — the Nut

4. Release a fixing nut and liberate тросовую draught from a basic arm.

5. Take draught from under the car.

6. Check up draught on presence of damages, in case of need make its replacement.

INSTALLATION

 PERFORMANCE ORDER

Installation is made in an order, the return to an order of dismantle of components.

CHECK

 PERFORMANCE ORDER

1. Make sure of serviceability of switching of modes «Hi» and «Lo». In case of need make adjustment приводной draughts (see more low).
2. Make sure of smoothness of a course drive a cable. In case of revealing of points of jamming make necessary regenerative repair, or replace draught assemblage.

ADJUSTMENT

 PERFORMANCE ORDER

1. Translate the lever of switching of modes in position «Hi».
2. Remove the handle of the lever of switching of modes (see Has undressed Removal, service and installation of the lever of switching of modes «Hi/Lo» an additional two-level reducer).
3. Remove the central console (the Body see the Head).
4. Loosen the a nut.
5. Be convinced that transmission is in position «Hi», - in case of need achieve demanded result by procrastination тросовой draught, then tighten a nut with demanded effort (18 Nanometers).
6. Check up serviceability of switching of modes of a 2-step reducer, in case of need repeat adjustment.

On the main page