Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
- Manual box and differential
   Specifications
   The mechanism of blocking of inclusion of a reverse gear - the device and a functioning principle
   Interaxal differential - the device and a functioning principle
   Removal and installation трансмиссионной assemblages
   Check of a condition and replacement of elements of support of a suspension bracket трансмиссионной assemblages
   Check of a condition and epiploon replacement
   Removal, installation and check of a condition of gauges-switches
   Removal, installation and check of a condition of the gauge of speed (VSS)
   Preparation for performance of major repairs РКПП
   Removal, service and installation of a distributing box and transmission lengthening
   Removal, service and installation of a leading gear wheel of the distributing mechanism
   Removal, service and installation of a conducted gear wheel of the distributing mechanism
   Removal, service and installation of interaxal differential
   Removal, service, installation and adjustment of assemblage of the mechanism of blocking of inclusion of a reverse gear
   Removal, installation and condition check картера трансмиссионной assemblages
   Removal, service, installation and adjustment of primary shaft РКПП
   Removal, service and installation of entrance shaft РКПП (models with an additional two-level reducer)
   Removal, service and installation of assemblage of a shaft of a leading gear wheel of the main transfer of a drive of forward wheels
   Removal, service, installation and adjustment of forward differential
   Removal, installation and check of a condition of a gear wheel of a drive of a speedometer
   Removal, installation and adjustment of an intermediate gear wheel of a reverse gear
   Removal, installation, check and adjustment of assemblage of gear wheels of a two-level reducer
   Removal, check of a condition and installation of plugs and gear change rods
   Removal, service and installation of the lever of gear change РКПП
   Removal, service and installation of the lever of switching of modes «Hi/Lo» an additional two-level reducer
   Removal, service and installation тросовой draughts of a drive of switching of modes of a two-level reducer
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal and installation трансмиссионной assemblages

Subject рассоединению contact sockets of electroconducting

And — the Socket of the gauge-switch of neutral position of transmission (Brown)
In — the Socket of the gauge-switch of fires of a backing (Grey)

With — the Socket of the gauge-switch of switching of modes «Hi/Lo» (Black), - models with an additional 2-step reducer


 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props. Remove protection картера, Turn out a drain stopper and merge трансмиссионное oil, then wrap a stopper with demanded effort, - do not forget to establish a sealing washer.
2. Completely open a cowl and prop up its rack.
3. Disconnect a negative wire from the battery.
4. Establish the gear change lever in position «N» and release a lay brake.
5. Disconnect a sleeve of an air inlet and remove an air cleaner (see the Head of the Power supply system and release).
6. Remove a basic arm of an air cleaner (see the Head of the Power supply system and release).

7. Disconnect from картера transmissions the grounding tyre, also disconnect electroconducting from gauges-switches of neutral position of transmission, fires of a backing and modes «Hi/Lo» (models with an additional 2-step reducer), disunite a contact socket of the gauge of speed of movement of the car (VSS).

8. On models with a 2-step reducer расшплинтуйте also take a fastening pin drive a cable of a choice of modes, remove a cable.

A — Shplint
B — the Pin
C — Privodnoj a cable of a choice of transfer

9. Remove a starter (the engine Electric equipment see the Head).

10. Remove from transmission the executive cylinder of coupling.

A — the Hose of a path of a hydrodrive of coupling
B — the Executive cylinder

11. Remove the terminator of rocking of the power unit.

Efforts of a tightening of carving connections, Nanometer

Т1: 50
Т2: 58

12. By means of special adaptation ST 41099AA010/41099АА020 fix the engine.

13. Turn out the top bolts of fastening of transmission to the engine.

14. Remove protection картера.
15. Remove reception and central sections of system of release of the fulfilled gases (see the Head of the Power supply system and release).
16. Remove back section of system of release of the fulfilled gases with the muffler (see the Head of the Power supply system and release).

17. Uncover a thermofilter.

18. Remove a basic arm подвеса on the right side картера transmissions.

19. Remove карданный a shaft (Coupling see the Head).
20. Remove from transmission a rack and a gear change rod.

And — the Rack
In — the Rod

21. Disconnect from the cross-section lever a rack of the stabilizer of cross-section stability.

22. Turn out a bolt of fastening of a spherical support of the cross-section lever to ступичной to assemblage.

23. Remove подпружиненные pins and liberate from transmission forward power shafts.

 Pins is subject to replacement without fail.

24. Give the bottom nuts of fastening of transmission to the engine.

25. Prop up a transmission special трансмиссионным a jack.

26. Remove a back cross-section beam of transmission.

Efforts of a tightening of carving connections, Nanometer

Т1: 70
Т2: 140

27. Moving a jack back, accurately liberate primary/entrance shaft РКПП from a coupling basket.
28. Definitively separate a transmission from the engine and remove a rubber pillow of a back support of a suspension bracket of the power unit.
29. Installation is made upside-down. Track, that all fixture has been tightened with demanded effort (Specifications and accompanying illustrations to the present Section see).


On the main page