Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
- Manual box and differential
   Specifications
   The mechanism of blocking of inclusion of a reverse gear - the device and a functioning principle
   Interaxal differential - the device and a functioning principle
   Removal and installation трансмиссионной assemblages
   Check of a condition and replacement of elements of support of a suspension bracket трансмиссионной assemblages
   Check of a condition and epiploon replacement
   Removal, installation and check of a condition of gauges-switches
   Removal, installation and check of a condition of the gauge of speed (VSS)
   Preparation for performance of major repairs РКПП
   Removal, service and installation of a distributing box and transmission lengthening
   Removal, service and installation of a leading gear wheel of the distributing mechanism
   Removal, service and installation of a conducted gear wheel of the distributing mechanism
   Removal, service and installation of interaxal differential
   Removal, service, installation and adjustment of assemblage of the mechanism of blocking of inclusion of a reverse gear
   Removal, installation and condition check картера трансмиссионной assemblages
   Removal, service, installation and adjustment of primary shaft РКПП
   Removal, service and installation of entrance shaft РКПП (models with an additional two-level reducer)
   Removal, service and installation of assemblage of a shaft of a leading gear wheel of the main transfer of a drive of forward wheels
   Removal, service, installation and adjustment of forward differential
   Removal, installation and check of a condition of a gear wheel of a drive of a speedometer
   Removal, installation and adjustment of an intermediate gear wheel of a reverse gear
   Removal, installation, check and adjustment of assemblage of gear wheels of a two-level reducer
   Removal, check of a condition and installation of plugs and gear change rods
   Removal, service and installation of the lever of gear change РКПП
   Removal, service and installation of the lever of switching of modes «Hi/Lo» an additional two-level reducer
   Removal, service and installation тросовой draughts of a drive of switching of modes of a two-level reducer
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal, installation and check of a condition of the gauge of speed (VSS)

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Поддомкратьте the car also establish it on props.
3. Remove a collector with its receiver.
4. Separate socket VSS.

5. Turn and remove VSS.

INSTALLATION

 PERFORMANCE ORDER

 Removed VSS is subject to replacement without fail. Before installation make sure of cleanliness of an aperture under gauge landing. Track correctness of combination of the thin end шпонки with шпоночным a groove on a pin of a shaft of a speedometer.

1. Manually screw VSS in a landing aperture, then tighten it with demanded effort (5.9 Nanometers).
2. Connect a contact socket of electroconducting of the gauge.
3. The further installation is made in an order, the return to an order of dismantle of components.

CHECK



 PERFORMANCE ORDER

1. Make sure of serviceability of functioning of a speedometer. At positive results of check pass to a following stage, otherwise measure resistance of a speedometer. The result of measurement between sinus and косинусными plugs should make 208 ± 8 Ohm, otherwise follows will replace the fan and assemblage from a measuring instrument of the expense of fuel. If the speedometer is perfectly in order, replace the printed-circuit board of a combination of devices.

2. Switch off ignition and measure resistance between the plug № 24 contact sockets ECM (В135) and the plug № 13 contact sockets of a combination of devices (i10). If the result of measurement makes less than 10 Ohm, replace socket ECM, otherwise eliminate breakage of electroconducting or infringement of quality of contact connections in sockets В135/В36.

On the main page