Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
   Specifications
   Brake mechanisms of forward and back wheels - the general information
   Lay brake - a design and a functioning principle
   The pressure valve-terminator - a design and a functioning principle
   Protivootkatnaja system - the device, a functioning and safety measure principle
   System of antiblocking of brakes (ABS) - the general information, a functioning principle
   System of dynamic stabilisation (VDC) - the general information, a functioning principle
   Check of a condition replacement колодок disk brake mechanisms of forward wheels
   Removal, check of a condition and installation of forward brake disks
   Removal, service and installation of disk brake mechanisms of forward wheels
   Check of a condition and replacement колодок disk brake mechanisms of back wheels
   Removal, check of a condition and installation of back brake disks
   Removal, service and installation of disk brake mechanisms of back wheels
   Removal, service and installation of the main brake cylinder (ГТЦ)
   Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
   Removal, installation and check of serviceability of functioning of the valve-terminator of pressure
   Replacement of a brake liquid
   Prorolling of a hydraulic path of brake system
   Check of a condition and replacement of flexible brake hoses
   Check of a condition and replacement of tubes of a brake path
   Removal, service, installation and adjustment of a pedal of a foot brake
   Removal, condition check, installation and adjustment of the gauge-switch of stoplights
   Removal, installation, check of a condition and adjustment of the lever of a drive of a lay brake
   Removal, check of a condition and installation of elements тросового a drive of a lay brake
   Removal, installation and adjustment of the mechanism of a lay brake
   Removal, installation, check of a condition and adjustment of components противооткатного devices
   Removal, installation and check of serviceability of functioning of assemblage of the module of management/hydromodulator ABS
   Check of sequence of operation of valves of hydromodulator ABS
   Removal, installation and check of serviceability of functioning of forward wheel gauges ABS
   Removal, installation and check of serviceability of functioning of back wheel gauges ABS
   Removal, installation and check of a condition of rotors of wheel gauges
   Removal, installation and diagnostics of the gauge of overloads (G-gauge)
   Problem diagnostics ABS
   Removal, installation and adjustment of the module of management VDC
   Removal, installation and check of serviceability of functioning of hydromodulator VDC
   Check of sequence of operation of valves of hydromodulators ABS and VDC
   Removal, installation and check of serviceability of functioning of the gauge of withdrawal / cross-section overloads
   Removal, installation and check of serviceability of functioning of the gauge of an angle of rotation of steering wheel VDC
   Removal, installation and check of serviceability of functioning of wheel gauges from rotors
   Removal, installation and check of serviceability of functioning of the switch of deactivation VDC (VDC OFF)
   Problem diagnostics VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal, service and installation of disk brake mechanisms of back wheels

REMOVAL

 PERFORMANCE ORDER

The order of performance of procedure is similar described in corresponding subsection Has undressed Removal, check of a condition and installation of forward brake disks.

DISMANTLING

 PERFORMANCE ORDER

1. Having hooked a screw-driver, remove a fixing ring dusterа the piston.

2. Remove duster.

3. Slowly submitting to the union of connection of a flexible brake hose the compressed air, push out the piston from the cylinder, - before a piston end face establish wooden брусок in the thickness of an order of 30 mm.

4. Having hooked a screw-driver, take from the cylinder of a support a piston cuff.

5. Remove from the support case a protective cover and the plug of a lock bolt (finger).
6. Remove a protective cover of a directing bolt (finger).
7. Attentively study a condition of the removed components. Check up the case of a support and the piston on presence of signs of non-uniform deterioration, mechanical damages and traces of development of corrosion. Make sure of absence of signs of ageing of a material dusterа, a cuff and protective covers. Defective components replace within the limits of let out ремнаборов.

ASSEMBLAGE

 PERFORMANCE ORDER

Operate according to the instructions resulted in corresponding subsection Has undressed Removal, service and installation of disk brake mechanisms of forward wheels.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. The order of installation brake колодок is described in Section Check of a condition and replacement колодок disk brake mechanisms of back wheels. The effort of a tightening of bolts of fastening анкерной скобы makes 78 Nanometers. Bolts of fastening of the case of a support are tightened with effort of 39 Nanometers, штуцерный a bolt - with effort of 18 Nanometers.

 Copper sealing washers штуцерного a socket of a flexible brake hose are subject to replacement without fail! Track, that the hose at connection has not appeared is overwound!


On the main page