Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
   Specifications
   Brake mechanisms of forward and back wheels - the general information
   Lay brake - a design and a functioning principle
   The pressure valve-terminator - a design and a functioning principle
   Protivootkatnaja system - the device, a functioning and safety measure principle
   System of antiblocking of brakes (ABS) - the general information, a functioning principle
   System of dynamic stabilisation (VDC) - the general information, a functioning principle
   Check of a condition replacement колодок disk brake mechanisms of forward wheels
   Removal, check of a condition and installation of forward brake disks
   Removal, service and installation of disk brake mechanisms of forward wheels
   Check of a condition and replacement колодок disk brake mechanisms of back wheels
   Removal, check of a condition and installation of back brake disks
   Removal, service and installation of disk brake mechanisms of back wheels
   Removal, service and installation of the main brake cylinder (ГТЦ)
   Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
   Removal, installation and check of serviceability of functioning of the valve-terminator of pressure
   Replacement of a brake liquid
   Prorolling of a hydraulic path of brake system
   Check of a condition and replacement of flexible brake hoses
   Check of a condition and replacement of tubes of a brake path
   Removal, service, installation and adjustment of a pedal of a foot brake
   Removal, condition check, installation and adjustment of the gauge-switch of stoplights
   Removal, installation, check of a condition and adjustment of the lever of a drive of a lay brake
   Removal, check of a condition and installation of elements тросового a drive of a lay brake
   Removal, installation and adjustment of the mechanism of a lay brake
   Removal, installation, check of a condition and adjustment of components противооткатного devices
   Removal, installation and check of serviceability of functioning of assemblage of the module of management/hydromodulator ABS
   Check of sequence of operation of valves of hydromodulator ABS
   Removal, installation and check of serviceability of functioning of forward wheel gauges ABS
   Removal, installation and check of serviceability of functioning of back wheel gauges ABS
   Removal, installation and check of a condition of rotors of wheel gauges
   Removal, installation and diagnostics of the gauge of overloads (G-gauge)
   Problem diagnostics ABS
   Removal, installation and adjustment of the module of management VDC
   Removal, installation and check of serviceability of functioning of hydromodulator VDC
   Check of sequence of operation of valves of hydromodulators ABS and VDC
   Removal, installation and check of serviceability of functioning of the gauge of withdrawal / cross-section overloads
   Removal, installation and check of serviceability of functioning of the gauge of an angle of rotation of steering wheel VDC
   Removal, installation and check of serviceability of functioning of wheel gauges from rotors
   Removal, installation and check of serviceability of functioning of the switch of deactivation VDC (VDC OFF)
   Problem diagnostics VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal, installation, check of a condition and adjustment of components противооткатного devices

Descriptions of a design and functioning principle противооткатного devices are resulted in Razdele Protivootkatnaja system - the device, a functioning and safety measure principle.

Details of fastening of a cable of a drive of valve PHV to a coupling pedal

1 — the Lock ring
2 — a coupling Pedal

3 — the Clamp
4 — Cable PHV

REMOVAL

The valve of deduction of pressure (PHV)

 PERFORMANCE ORDER

1. Pump out a hydraulic liquid from tank GTTS.
2. Execute procedures of paragraphs with 2 under 6 of Section Removal, service, installation and adjustment of a pedal of a foot brake.
3. Disconnect from valve PHV brake tubes, - try not to admit hit of a brake liquid on painted кузовные a surface, in case of need at once collect the spilt liquid paper towels.

 Отпускание штуцерных nuts it is necessary to make by means of special накидного a key with a cutting head!


4. Turn out fixing bolts and remove valve PHV in gathering with a basic arm from a lateral beam.

 Try not to admit hits in клапанную assemblage of extraneous particles!


Privodnoj cable of valve PHV

 PERFORMANCE ORDER

1. Disconnect a cable from valve PHV (see Has undressed Removal, service, installation and adjustment of a pedal of a foot brake).
2. Remove a coupling pedal (Coupling see the Head).
3. Disconnect a cable from a pedal of coupling and remove it from the car.

CHECK

 PERFORMANCE ORDER

1. Check up a condition of protective covers, a cover and the core drive a cable, estimate course freedom тросовой assemblages. Estimate degree of deterioration of a returnable spring, check up it on presence of signs of development of corrosion and mechanical damages.
2. Shake the valve, - the sound перекатывания a ball confirms serviceability of a condition of assemblage. Manually check up smoothness of rotation of the lever.

 Valve PHV is not subject to regenerative repair and in case of failure is replaced in gathering!

INSTALLATION

Valve PHV

 PERFORMANCE ORDER

1. Establish valve PHV on the regular place on a lateral beam. Also tighten fixing bolts with demanded effort (18 Nanometers).Подсоедините to the valve hydraulic tubes, - накидные nuts штуцерных connections are tightened with effort of 15 Nanometers.

 Try not to deform a tube in the course of their connection, in case of need replace the damaged sections.

2. Connect to the executive lever of the valve приводной a cable, - in case of need replace the damaged clamps.

 Do not suppose перегибания a cable under excessive corners! A zatsepnuju part of a returnable spring and a point of fastening of a cable on the executive lever of the valve preliminary grease with greasing SUNLIGHT 2 (№ 003602010).

3. Pump over brake system (the Section Prorolling of a hydraulic path of brake system see). In case of need make adjustment drive cable PHV (see more low).


Privodnoj cable of valve PHV

 PERFORMANCE ORDER

 The damaged cable is subject to replacement without fail.

1. Installation is made in an order, the return to an order of dismantle of components, - do not suppose перегибания a cable under excessive corners. The zatsepnoj end of a returnable spring and a point of fastening of a cable on the executive lever of the valve preliminary grease with greasing SUNLIGHT 2 (№ 003602010).
2. In case of need make adjustment drive cable PHV (see more low).

ADJUSTMENT

 PERFORMANCE ORDER

 Before to start adjustment of the replaced cable of drive PHV squeeze out a pedal of coupling of an order of 30 times.

1. Drive away the car on road going uphill and check up serviceability of functioning противооткатного devices (Razdel Protivootkatnaja system - the device, a functioning and safety measure principle see). If the car does not stop, tighten adjusting cable nuts.
2. Serviceability infringement трогания the car can speak one of two reasons:

a) Otpuskanie противооткатного devices occurs earlier, than coupling (the engine begins глохнуть) is activated, - gradually release an adjusting nut and repeat check until will achieve satisfactory result;
b) Otpuskanie противооткатного devices occurs later, than coupling (the car slightly slides off downwards) is activated, - tighten a nut before occurrence of the signs described in point (then, gradually releasing a nut, achieve demanded result.
3. Having finished adjustment, tighten with demanded effort (3.4 Nanometers) a counternut.

On the main page