Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
   Specifications
   Brake mechanisms of forward and back wheels - the general information
   Lay brake - a design and a functioning principle
   The pressure valve-terminator - a design and a functioning principle
   Protivootkatnaja system - the device, a functioning and safety measure principle
   System of antiblocking of brakes (ABS) - the general information, a functioning principle
   System of dynamic stabilisation (VDC) - the general information, a functioning principle
   Check of a condition replacement колодок disk brake mechanisms of forward wheels
   Removal, check of a condition and installation of forward brake disks
   Removal, service and installation of disk brake mechanisms of forward wheels
   Check of a condition and replacement колодок disk brake mechanisms of back wheels
   Removal, check of a condition and installation of back brake disks
   Removal, service and installation of disk brake mechanisms of back wheels
   Removal, service and installation of the main brake cylinder (ГТЦ)
   Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
   Removal, installation and check of serviceability of functioning of the valve-terminator of pressure
   Replacement of a brake liquid
   Prorolling of a hydraulic path of brake system
   Check of a condition and replacement of flexible brake hoses
   Check of a condition and replacement of tubes of a brake path
   Removal, service, installation and adjustment of a pedal of a foot brake
   Removal, condition check, installation and adjustment of the gauge-switch of stoplights
   Removal, installation, check of a condition and adjustment of the lever of a drive of a lay brake
   Removal, check of a condition and installation of elements тросового a drive of a lay brake
   Removal, installation and adjustment of the mechanism of a lay brake
   Removal, installation, check of a condition and adjustment of components противооткатного devices
   Removal, installation and check of serviceability of functioning of assemblage of the module of management/hydromodulator ABS
   Check of sequence of operation of valves of hydromodulator ABS
   Removal, installation and check of serviceability of functioning of forward wheel gauges ABS
   Removal, installation and check of serviceability of functioning of back wheel gauges ABS
   Removal, installation and check of a condition of rotors of wheel gauges
   Removal, installation and diagnostics of the gauge of overloads (G-gauge)
   Problem diagnostics ABS
   Removal, installation and adjustment of the module of management VDC
   Removal, installation and check of serviceability of functioning of hydromodulator VDC
   Check of sequence of operation of valves of hydromodulators ABS and VDC
   Removal, installation and check of serviceability of functioning of the gauge of withdrawal / cross-section overloads
   Removal, installation and check of serviceability of functioning of the gauge of an angle of rotation of steering wheel VDC
   Removal, installation and check of serviceability of functioning of wheel gauges from rotors
   Removal, installation and check of serviceability of functioning of the switch of deactivation VDC (VDC OFF)
   Problem diagnostics VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal, installation and check of serviceability of functioning of back wheel gauges ABS

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Поддомкратьте the car also establish it on props.

3. Remove a filter of a fuel tank.

4. Disconnect electroconducting of the wheel gauge.

5. Release an intermediate clamp of fastening of a plait of electroconducting of the gauge on кузовном an element.

6. Turn out bolts of fastening of basic arms of a plait.

7. Remove gauge ABS from the suspension bracket lever, - do not pull the gauge for an electroconducting plait, try not to damage a polar tip.

8. For check of a condition of a rotor of the gauge which has been built in in шарнирную assemblage, remove a power shaft.

CHECK

 PERFORMANCE ORDER

 The Section Problem diagnostics ABS see also.

The description of procedures of check and adjustment of wheel gauges is resulted in Section Removal, installation and check of serviceability of functioning of forward wheel gauges ABS from that only a difference that the nominal size of a working backlash (S) makes for back gauges 0.44 ÷ 0.94 mm. Adjustment is made by lining selection № 26755АА000.

INSTALLATION

 PERFORMANCE ORDER

Installation is made in an order, the return to an order of dismantle of components. Track correctness of a lining and reliability of fixing of a plait of electroconducting (the left gauge - yellow isolation, right - white). All fixture should be tightened with demanded effort (Specifications and accompanying illustrations to subsection "Removal" see). Do not forget to adjust working backlashes by lining selection № 26755АА000.


On the main page