Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
Specifications
Brake mechanisms of forward and back wheels - the general information
Lay brake - a design and a functioning principle
The pressure valve-terminator - a design and a functioning principle
Protivootkatnaja system - the device, a functioning and safety measure principle
System of antiblocking of brakes (ABS) - the general information, a functioning principle
System of dynamic stabilisation (VDC) - the general information, a functioning principle
Check of a condition replacement колодок disk brake mechanisms of forward wheels
Removal, check of a condition and installation of forward brake disks
Removal, service and installation of disk brake mechanisms of forward wheels
Check of a condition and replacement колодок disk brake mechanisms of back wheels
Removal, check of a condition and installation of back brake disks
Removal, service and installation of disk brake mechanisms of back wheels
Removal, service and installation of the main brake cylinder (ГТЦ)
Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
Removal, installation and check of serviceability of functioning of the valve-terminator of pressure
Replacement of a brake liquid
Prorolling of a hydraulic path of brake system
Check of a condition and replacement of flexible brake hoses
Check of a condition and replacement of tubes of a brake path
Removal, service, installation and adjustment of a pedal of a foot brake
Removal, condition check, installation and adjustment of the gauge-switch of stoplights
Removal, installation, check of a condition and adjustment of the lever of a drive of a lay brake
Removal, check of a condition and installation of elements тросового a drive of a lay brake
Removal, installation and adjustment of the mechanism of a lay brake
Removal, installation, check of a condition and adjustment of components противооткатного devices
Removal, installation and check of serviceability of functioning of assemblage of the module of management/hydromodulator ABS
Check of sequence of operation of valves of hydromodulator ABS
Removal, installation and check of serviceability of functioning of forward wheel gauges ABS
Removal, installation and check of serviceability of functioning of back wheel gauges ABS
Removal, installation and check of a condition of rotors of wheel gauges
Removal, installation and diagnostics of the gauge of overloads (G-gauge)
Problem diagnostics ABS
Removal, installation and adjustment of the module of management VDC
Removal, installation and check of serviceability of functioning of hydromodulator VDC
Check of sequence of operation of valves of hydromodulators ABS and VDC
Removal, installation and check of serviceability of functioning of the gauge of withdrawal / cross-section overloads
Removal, installation and check of serviceability of functioning of the gauge of an angle of rotation of steering wheel VDC
Removal, installation and check of serviceability of functioning of wheel gauges from rotors
Removal, installation and check of serviceability of functioning of the switch of deactivation VDC (VDC OFF)
Problem diagnostics VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal, installation, check of a condition and adjustment of the lever of a drive of a lay brake
REMOVAL
|
|
|
1. Поддомкратьте the car also establish it on props.
2. Remove back wheels.
3. Remove the central console (the Body see the Head).
4. Release an adjusting nut drive a cable of a lay brake in the basis of lever assemblage.
|
|
5. Give fixture and remove assemblage of the lever of raising of a lay brake. |
|
|
6. Unbend a lock uvula on the lever and disconnect приводной a cable.
1 — the Lever
2 — Privodnoj a cable |
|
|
INSTALLATION
|
|
|
Installation is made upside-down. The lever fixture is tightened with effort of 18 Nanometers, an adjusting nut - with effort of 5.9 Nanometers. Track, that приводной the cable is passed in directing tunnel. In summary make lever adjustment (see more low). |
|
Check and adjustment
|
|
|
1. Count quantity of clicks of a ratchet at raising of the lever with effort nearby 20 кГс (196). If the quantity of clicks does not correspond to standard requirements (7 ÷ 8), make necessary adjustment (see further).
|
|
2. Uncover the central console. 3-5 times with effort cock the lever of a lay brake. Rotation of a regulator achieve demanded quantity of clicks at raising of the lever with effort 20 кГс, then tighten a counternut with demanded effort (5.9 Nanometers). In case of need make adjustment brake mechanisms of back wheels (see Has undressed Removal, installation and adjustment of the mechanism of a lay brake).
1 — the Lever
2 — the Counternut
3 — the Adjusting nut |
3. Establish into place a cover of the central console. |
|
|
On the main page
|