Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
   Specifications
   Brake mechanisms of forward and back wheels - the general information
   Lay brake - a design and a functioning principle
   The pressure valve-terminator - a design and a functioning principle
   Protivootkatnaja system - the device, a functioning and safety measure principle
   System of antiblocking of brakes (ABS) - the general information, a functioning principle
   System of dynamic stabilisation (VDC) - the general information, a functioning principle
   Check of a condition replacement колодок disk brake mechanisms of forward wheels
   Removal, check of a condition and installation of forward brake disks
   Removal, service and installation of disk brake mechanisms of forward wheels
   Check of a condition and replacement колодок disk brake mechanisms of back wheels
   Removal, check of a condition and installation of back brake disks
   Removal, service and installation of disk brake mechanisms of back wheels
   Removal, service and installation of the main brake cylinder (ГТЦ)
   Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
   Removal, installation and check of serviceability of functioning of the valve-terminator of pressure
   Replacement of a brake liquid
   Prorolling of a hydraulic path of brake system
   Check of a condition and replacement of flexible brake hoses
   Check of a condition and replacement of tubes of a brake path
   Removal, service, installation and adjustment of a pedal of a foot brake
   Removal, condition check, installation and adjustment of the gauge-switch of stoplights
   Removal, installation, check of a condition and adjustment of the lever of a drive of a lay brake
   Removal, check of a condition and installation of elements тросового a drive of a lay brake
   Removal, installation and adjustment of the mechanism of a lay brake
   Removal, installation, check of a condition and adjustment of components противооткатного devices
   Removal, installation and check of serviceability of functioning of assemblage of the module of management/hydromodulator ABS
   Check of sequence of operation of valves of hydromodulator ABS
   Removal, installation and check of serviceability of functioning of forward wheel gauges ABS
   Removal, installation and check of serviceability of functioning of back wheel gauges ABS
   Removal, installation and check of a condition of rotors of wheel gauges
   Removal, installation and diagnostics of the gauge of overloads (G-gauge)
   Problem diagnostics ABS
   Removal, installation and adjustment of the module of management VDC
   Removal, installation and check of serviceability of functioning of hydromodulator VDC
   Check of sequence of operation of valves of hydromodulators ABS and VDC
   Removal, installation and check of serviceability of functioning of the gauge of withdrawal / cross-section overloads
   Removal, installation and check of serviceability of functioning of the gauge of an angle of rotation of steering wheel VDC
   Removal, installation and check of serviceability of functioning of wheel gauges from rotors
   Removal, installation and check of serviceability of functioning of the switch of deactivation VDC (VDC OFF)
   Problem diagnostics VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal, check of a condition and installation of forward brake disks

REMOVAL

 PERFORMANCE ORDER

1. Release wheel nuts, поддомкратьте redock of the car and establish it on props, remove a corresponding wheel.

2. Remove a brake support (see Has undressed Removal, service and installation of disk brake mechanisms of forward wheels) and, without disconnecting a flexible hydraulic hose, tie up its wire to suspension bracket elements. Remove анкерную скобу the brake mechanism.

3. Remove a brake disk. If the disk "has become attached" and does not give in to removal, screw in apertures In in ступичной its parts pair of bolts М8 and gradually in regular intervals tighten them, wringing out a disk with ступичной assemblages.

And — the Thickness of a brake disk
In — Apertures in ступичной disk parts

CHECK

 PERFORMANCE ORDER

1. Plant a disk on ступичную assemblage and fix its wheel nuts. Fix on a rack циферблатный a measuring instrument плунжерного type and, rotating a disk, define size of its lateral palpation.

 Плунжер a measuring instrument should rest against a disk on distance about 5 millimetres to the centre from external edge of a disk.

2. Compare result of measurement to requirements of Specifications, in case of need replace a disk, preliminary having made sure that a cause of infringement is not axial люфт the wheel bearing, or palpation ступичной assemblages (the Suspension bracket and a steering see the Head).
3. In several points measure a thickness of a disk, closing micrometer sponges on distance about 5 mm from external edge of a disk. Compare results of measurement to requirements of Specifications. In case of need replace a disk.

INSTALLATION

 PERFORMANCE ORDER

Installation is made in an order, the return to an order of dismantle of components. The effort of a tightening of bolts of fastening анкерной скобы a support makes 78 Nanometers.

On the main page