Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
Specifications
Brake mechanisms of forward and back wheels - the general information
Lay brake - a design and a functioning principle
The pressure valve-terminator - a design and a functioning principle
Protivootkatnaja system - the device, a functioning and safety measure principle
System of antiblocking of brakes (ABS) - the general information, a functioning principle
System of dynamic stabilisation (VDC) - the general information, a functioning principle
Check of a condition replacement колодок disk brake mechanisms of forward wheels
Removal, check of a condition and installation of forward brake disks
Removal, service and installation of disk brake mechanisms of forward wheels
Check of a condition and replacement колодок disk brake mechanisms of back wheels
Removal, check of a condition and installation of back brake disks
Removal, service and installation of disk brake mechanisms of back wheels
Removal, service and installation of the main brake cylinder (ГТЦ)
Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
Removal, installation and check of serviceability of functioning of the valve-terminator of pressure
Replacement of a brake liquid
Prorolling of a hydraulic path of brake system
Check of a condition and replacement of flexible brake hoses
Check of a condition and replacement of tubes of a brake path
Removal, service, installation and adjustment of a pedal of a foot brake
Removal, condition check, installation and adjustment of the gauge-switch of stoplights
Removal, installation, check of a condition and adjustment of the lever of a drive of a lay brake
Removal, check of a condition and installation of elements тросового a drive of a lay brake
Removal, installation and adjustment of the mechanism of a lay brake
Removal, installation, check of a condition and adjustment of components противооткатного devices
Removal, installation and check of serviceability of functioning of assemblage of the module of management/hydromodulator ABS
Check of sequence of operation of valves of hydromodulator ABS
Removal, installation and check of serviceability of functioning of forward wheel gauges ABS
Removal, installation and check of serviceability of functioning of back wheel gauges ABS
Removal, installation and check of a condition of rotors of wheel gauges
Removal, installation and diagnostics of the gauge of overloads (G-gauge)
Problem diagnostics ABS
Removal, installation and adjustment of the module of management VDC
Removal, installation and check of serviceability of functioning of hydromodulator VDC
Check of sequence of operation of valves of hydromodulators ABS and VDC
Removal, installation and check of serviceability of functioning of the gauge of withdrawal / cross-section overloads
Removal, installation and check of serviceability of functioning of the gauge of an angle of rotation of steering wheel VDC
Removal, installation and check of serviceability of functioning of wheel gauges from rotors
Removal, installation and check of serviceability of functioning of the switch of deactivation VDC (VDC OFF)
Problem diagnostics VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal, installation and check of serviceability of functioning of the valve-terminator of pressure
REMOVAL
|
|
|
1. Cock a lay brake and prop up противооткатными wheel boots.
2. Disconnect from the valve-terminator four brake tubes.
|
|
3. Turn out the fixing screw and remove the valve from a basic arm.
|
|
The valve-terminator to dismantling and regenerative repair be not subject and in case of failure should be replaced in gathering! |
|
|
|
INSTALLATION
|
|
|
1. Establish the valve-terminator on a basic arm and tighten a fixing bolt with effort of 15 Nanometers.
2. In the correct image connect to the valve-terminator brake tubes, - the effort of a tightening накидных nuts штуцерных connections makes 18 Nanometers.
3. Pump over brake system (the Section Prorolling of a hydraulic path of brake system see), then check up штуцерные connections on the valve-terminator on presence of signs of development of leaks. |
|
CHECK
|
|
|
1. Connect manometres for measurement of hydraulic pressure in forward (ГТЦ) and back brake contours (the wheel cylinder).
2. Remove from manometres air stoppers.
|
|
3. Squeezing out a pedal of a foot brake, remove dependence of pressure in the back wheel cylinder from pressure in ГТЦ. Value of a point of division is resulted in Specifications. |
|
|
|
On the main page
|