Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
   Specifications
   Brake mechanisms of forward and back wheels - the general information
   Lay brake - a design and a functioning principle
   The pressure valve-terminator - a design and a functioning principle
   Protivootkatnaja system - the device, a functioning and safety measure principle
   System of antiblocking of brakes (ABS) - the general information, a functioning principle
   System of dynamic stabilisation (VDC) - the general information, a functioning principle
   Check of a condition replacement колодок disk brake mechanisms of forward wheels
   Removal, check of a condition and installation of forward brake disks
   Removal, service and installation of disk brake mechanisms of forward wheels
   Check of a condition and replacement колодок disk brake mechanisms of back wheels
   Removal, check of a condition and installation of back brake disks
   Removal, service and installation of disk brake mechanisms of back wheels
   Removal, service and installation of the main brake cylinder (ГТЦ)
   Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
   Removal, installation and check of serviceability of functioning of the valve-terminator of pressure
   Replacement of a brake liquid
   Prorolling of a hydraulic path of brake system
   Check of a condition and replacement of flexible brake hoses
   Check of a condition and replacement of tubes of a brake path
   Removal, service, installation and adjustment of a pedal of a foot brake
   Removal, condition check, installation and adjustment of the gauge-switch of stoplights
   Removal, installation, check of a condition and adjustment of the lever of a drive of a lay brake
   Removal, check of a condition and installation of elements тросового a drive of a lay brake
   Removal, installation and adjustment of the mechanism of a lay brake
   Removal, installation, check of a condition and adjustment of components противооткатного devices
   Removal, installation and check of serviceability of functioning of assemblage of the module of management/hydromodulator ABS
   Check of sequence of operation of valves of hydromodulator ABS
   Removal, installation and check of serviceability of functioning of forward wheel gauges ABS
   Removal, installation and check of serviceability of functioning of back wheel gauges ABS
   Removal, installation and check of a condition of rotors of wheel gauges
   Removal, installation and diagnostics of the gauge of overloads (G-gauge)
   Problem diagnostics ABS
   Removal, installation and adjustment of the module of management VDC
   Removal, installation and check of serviceability of functioning of hydromodulator VDC
   Check of sequence of operation of valves of hydromodulators ABS and VDC
   Removal, installation and check of serviceability of functioning of the gauge of withdrawal / cross-section overloads
   Removal, installation and check of serviceability of functioning of the gauge of an angle of rotation of steering wheel VDC
   Removal, installation and check of serviceability of functioning of wheel gauges from rotors
   Removal, installation and check of serviceability of functioning of the switch of deactivation VDC (VDC OFF)
   Problem diagnostics VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal, installation and adjustment of the module of management VDC

1 — the Module of management VDC

Efforts of a tightening of carving connections, Nanometer

Т: 7.5

 

Removal and installation

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

2. Uncover panels of devices and disunite contact demountable electroconductings from its return party.

3. Turn out three fixing bolts and shift aside the assembly block of safety locks.

4. Turn out two bolts of fastening of the module of management VDC on a basic arm.

5. Disconnect electroconducting and remove the management module, having pulled upwards a lateral clamp.

6. Installation is made upside-down. At replacement of the module of management it is necessary to track conformity of its marks of model of the car (Specifications see).

1 — Spetsifikatsionnaja marks

7. On termination of installation follows make necessary adjustments (see more low).

ADJUSTMENT

 Installation of the central position of the gauge of an angle of rotation of a steering wheel and zeroing of the gauge of withdrawal / cross-section overloads should be made each time after removal/replacement of such components, as the module of management VDC, the withdrawal gauge / cross-section overloads, details of a steering column (including the module of a pillow of safety), suspension bracket details, and also after performance of adjustment of position of a steering wheel.


Without application SSM

 PERFORMANCE ORDER

 Whenever possible adjustment should be made with application of firm input reader Subaru (SSM).

1. Park the car on an equal horizontal platform, whenever possible with a firm covering.
2. Result forward wheels of the car in rectilinear position and check up steering wheel centering, in case of need make corresponding updating.
3. Make on the car short (an order of 10 km) a trip on direct roads with a good covering, switch off ignition, then again start the engine and during the following trip make sure that control lamp VDC is not activated during movement. Also try to make sure of serviceability of functioning VDC and a steering drive.


From application SSM

 PERFORMANCE ORDER

1. Park the car on an equal horizontal platform, whenever possible with a firm covering. Start the engine and leave its working on neutral transfer (АТ in position «N» or «Р»).
2. Result forward wheels of the car in rectilinear position and check up steering wheel centering, in case of need make corresponding updating.
3. Connect SSM to the car and choose in section of the menu of the display «Function Check Sequence» point «Set Mode Str. A.Sen. N and Lat. Gsen.0p» (follow displayed instructions).
4. In section {Brake Control System} the menu choose point «Current Data Display and Save» and make sure that the gauge of an angle of rotation of a steering wheel is nulled («0 deg»).
5. If the information on the gauge differs from stipulated above {0 deg}, adjust steering wheel position, then repeat check.
6. Make on the car short (an order of 10 km) a trip on direct roads with a good covering, switch off ignition, then again start the engine and during the following trip make sure that control lamp VDC is not activated during movement. Also try to make sure of serviceability of functioning VDC and a steering drive.


On the main page